
--------------------------------------------------------------------------------
 Second Boot by Nexell Co. : Built on Nov 19 2014 20:10:38
--------------------------------------------------------------------------------
 PLL0: 550000000   PLL1: 1200000000   PLL2: 800000000   PLL3: 612000000

 Divider0 PLL: 1 CPU:1200000000   CPU BUS:300000000
 Divider1 PLL: 2 BCLK:400000000   PCLK:200000000
 Divider2 PLL: 2 MDCLK:800000000   MCLK:800000000   
		 MBCLK:400000000   MPCLK:200000000
 Divider3 PLL: 0 G3D BCLK:550000000
 Divider4 PLL: 2 MPEG BCLK:400000000   MPEG PCLK:200000000

123
DDR3 POR Init Start
phy init

########## READ/GATE Level ##########
DDR3 Init Done!
Loading from sdmmc...
 Image Loading Done!
Launch to 0x42C00000


U-Boot 2014.07-gd46d757 (Nov 27 2015 - 17:09:12)

PLL : [0] =  550000000, [1] = 1200000000, [2] =  800000000, [3] =  614399000
PLL1: CPU FCLK = 1200000000, HCLK = 300000000
PLL2: BUS BCLK =  400000000, PCLK = 200000000
PLL2: MEM MCLK =  800000000, DCLK = 800000000, BCLK = 400000000, PCLK = 200000000
PLL0: G3D BCLK =  550000000
PLL2: MPG BCLK =  400000000, PCLK = 200000000
I2C:   ready
DRAM:  256 MiB
Heap = 0x43000000~0x45000000
Code = 0x42c00000~0x42c72984
GLD  = 0x42bffeb8
GLBD = 0x42bffe68
SP   = 0x42bffe68,0x42bffe50(CURR)
PC   = 0x42c06114
TAGS = 0x40000100 
PAGE = 0x42c80000~0x42c8c000
MACH = [4330]   
VER  = 1      
BOARD= [nanopi2]    
LCD  = N/A (-1)
MMC:   NXP DWMMC: 0, NXP DWMMC: 1, NXP DWMMC: 2
In:    serial
Out:   serial
Err:   serial
switch to partitions #0, OK
mmc0 is current device
Writing to MMC(0)... done
HDMI: display.0, preset 0 (1280 *  720)
HDMI: PHY Ready!!!
DONE: Logo bmp 800 by 480 (3bpp), len=1152056 

DRAW: 0x47000000 -> 0x46000000 

Hit any key to stop autoboot:  1  0 
## Booting kernel from Legacy Image at 48000000 ...
   Image Name:   Linux-3.4.39-FriendlyARM
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4767712 Bytes = 4.5 MiB
   Load Address: 40008000
   Entry Point:  40008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 3.4.39-FriendlyARM (root@jensen) (gcc version 4.9.3 (ctng-1.21.0-229g-FA) ) #1 SMP PREEMPT Sat Nov 28 17:36:10 HKT 2015
[    0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine: NANOPI2
[    0.000000] Display: HDMI selected
[    0.000000] nxp_reserve_mem: reserve CMA: size 201326592
[    0.000000] NXP/CMA: Reserved 0x74000000/0x0c000000 for 'ion'
[    0.000000] NXP/CMA: success register cma region for 'ion'
[    0.000000] Memory policy: ECC disabled, Data cache writealloc
[    0.000000] CPU : iomap[ 0]: p 0xc0000000 -> v 0xf0000000 len=0x300000
[    0.000000] CPU : iomap[ 1]: p 0xf0000000 -> v 0xf0300000 len=0x100000
[    0.000000] CPU : iomap[ 2]: p 0xcf000000 -> v 0xf0400000 len=0x100000
[    0.000000] CPU : iomap[ 3]: p 0x2c000000 -> v 0xf0500000 len=0x100000
[    0.000000] CPU : iomap[ 4]: p 0x00000000 -> v 0xf0600000 len=0x100000
[    0.000000] CPU : DMA Zone Size =16M, CORE 4
[    0.000000] CPU : VERSION = 2 (0xE153000A), Assign Peripheral Exclusive Bus
[    0.000000] s5p4418-NanoPi2: Board initialized
[    0.000000] CPU : Clock Generator= 64 EA, DVFS = support, PLL.1
[    0.000000] PLL : [0] =  550000000, [1] = 1200000000, [2] =  800000000, [3] =  614399000
[    0.000000] PLL1: CPU FCLK = 1200000000, HCLK = 300000000
[    0.000000] PLL2: BUS BCLK =  400000000, PCLK = 200000000
[    0.000000] PLL2: MEM MCLK =  800000000, DCLK = 800000000, BCLK = 400000000, PCLK = 200000000
[    0.000000] PLL0: G3D BCLK =  550000000
[    0.000000] PLL2: MPG BCLK =  400000000, PCLK = 200000000
[    0.000000] PERCPU: Embedded 8 pages/cpu @81339000 s12288 r8192 d12288 u32768
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 259840
[    0.000000] Kernel command line: console=ttyAMA0,115200n8 root=/dev/mmcblk0p2 rootfstype=ext4 init=/sbin/init lcd=HDMI720P60
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] allocated 2097152 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.000000] Memory: 1024MB = 1024MB total
[    0.000000] Memory: 829296k/829296k available, 219280k reserved, 0K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xc0800000 - 0xfee00000   ( 998 MB)
[    0.000000]     lowmem  : 0x80000000 - 0xc0000000   (1024 MB)
[    0.000000]     pkmap   : 0x7fe00000 - 0x80000000   (   2 MB)
[    0.000000]     modules : 0x7f000000 - 0x7fe00000   (  14 MB)
[    0.000000]       .text : 0x80008000 - 0x808a9244   (8837 kB)
[    0.000000]       .init : 0x808aa000 - 0x808e1000   ( 220 kB)
[    0.000000]       .data : 0x808e2000 - 0x80953d78   ( 456 kB)
[    0.000000]        .bss : 0x80953d9c - 0x80a31840   ( 887 kB)
[    0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] NR_IRQS:288
[    0.000000] VIC @f0002000: id 0x00041192, vendor 0x41
[    0.000000] VIC @f0003000: id 0x00041192, vendor 0x41
[    0.000000] GPIO  @f001a000: start  64, mask 0xffffffff (gpio 53)
[    0.000000] GPIO  @f001b000: start  96, mask 0xffffffff (gpio 54)
[    0.000000] GPIO  @f001c000: start 128, mask 0xffffffff (gpio 55)
[    0.000000] GPIO  @f001d000: start 160, mask 0xffffffff (gpio 56)
[    0.000000] GPIO  @f001e000: start 192, mask 0xffffffff (gpio 57)
[    0.000000] ALIVE @f0010800: start 224, mask 0x000000ff (alive 4)
[    0.000000] GIC   @f0301000: start 256 (vic 31)
[    0.000000] timer.0: source,  10000000(HZ:250), mult:3355443200
[    0.000000] timer.1: event ,  10000000(HZ:250), mult:42949673
[    0.000000] sched_clock: 32 bits at 250 Hz, resolution 4000000ns, wraps every 4294967292ms
[    0.000000] Console: colour dummy device 80x30
[    0.000000] Calibrating delay loop... 2390.01 BogoMIPS (lpj=4780032)
[    0.036000] pid_max: default: 32768 minimum: 301
[    0.036000] Security Framework initialized
[    0.036000] SELinux:  Initializing.
[    0.036000] Mount-cache hash table entries: 512
[    0.036000] Initializing cgroup subsys debug
[    0.036000] Initializing cgroup subsys cpuacct
[    0.036000] Initializing cgroup subsys memory
[    0.036000] Initializing cgroup subsys freezer
[    0.036000] CPU: Testing write buffer coherency: ok
[    0.036000] CPU0: thread -1, cpu 0, socket 10, mpidr 80000a00
[    0.036000] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[    0.036000] Setting up static identity map for 0x4065e408 - 0x4065e460
[    0.036000] L310 cache controller enabled
[    0.036000] l2x0: 16 ways, CACHE_ID 0x4100c4c8, AUX_CTRL 0x70470001, Cache size: 1048576 B
[    0.076000] CPU1: thread -1, cpu 1, socket 10, mpidr 80000a01
[    0.108000] CPU2: thread -1, cpu 2, socket 10, mpidr 80000a02
[    0.140000] CPU3: thread -1, cpu 3, socket 10, mpidr 80000a03
[    0.140000] Brought up 4 CPUs
[    0.140000] SMP: Total of 4 processors activated (9560.06 BogoMIPS).
[    0.140000] devtmpfs: initialized
[    0.144000] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    0.144000] pwm: max = 50000000 hz
[    0.144000] prepare_gpio_suspend:
[    0.144000]   alfn[0][0]: 0x00000000, alfn[0][1]: 0x00000000
[    0.144000]   alfn[1][0]: 0x66800000, alfn[1][1]: 0x55555566
[    0.144000]   alfn[2][0]: 0x55555555, alfn[2][1]: 0x00555555
[    0.144000]   alfn[3][0]: 0x00000000, alfn[3][1]: 0x00000000
[    0.144000]   alfn[4][0]: 0x00000000, alfn[4][1]: 0x55540000
[    0.144000] dummy: 
[    0.144000] NET: Registered protocol family 16
[    0.144000] [Register machine platform devices]
[    0.144000] mach: add amba device uart-pl011.0 
[    0.144000] mach: add amba device uart-pl011.1 
[    0.144000] mach: add amba device pl08xdmac.0 
[    0.144000] mach: add amba device pl08xdmac.1 
[    0.144000] mach: add amba device ssp-pl022.0 
[    0.144000] mach: add device syncgen [2]
[    0.148000] mach: add device hdmi 
[    0.148000] mach: add device i2c bus (array:3) 
[    0.148000] mach: add device Real Time Clock  
[    0.148000] mach: add device generic pwm (array:1)
[    0.148000] mach: add device generic gpio (array:6)
[    0.148000] mach: add device i2s (array:1) 
[    0.148000] mach: add device spdif tx
[    0.148000] mach: add device usb_ehci
[    0.148000] mach: add device usb_ohci
[    0.148000] mach: add device usb otg
[    0.148000] mach: add device ion-nxp
[    0.148000] mach: add device adc
[    0.148000] mach: add graphic device opengl|es
[    0.148000] [Register board platform devices]
[    0.148000] plat: board revision 0
[    0.148000] plat: add dynamic frequency (pll.1)
[    0.148000] plat: add framebuffer
[    0.148000] plat: add device sdmmc [0]
[    0.148000] plat: add device sdmmc [1]
[    0.148000] plat: add device sdmmc [2]
[    0.148000] plat: add backlight pwm device
[    0.148000] plat: add device keypad
[    0.148000] plat: add device fixed voltage
[    0.152000] plat: add device spdif playback
[    0.152000] plat: add device nxp-v4l2
[    0.152000] plat: register spidev
[    0.152000] plat: add touch(ft5x0x) device
[    0.152000] plat: add device gpio_led
[    0.152000] 
[    0.152000] hw-breakpoint: Debug register access (0xee113e95) caused undefined instruction on CPU 2
[    0.152000] hw-breakpoint: Debug register access (0xee113e95) caused undefined instruction on CPU 1
[    0.152000] hw-breakpoint: Debug register access (0xee113e95) caused undefined instruction on CPU 3
[    0.152000] hw-breakpoint: CPU 1 debug is powered down!
[    0.152000] hw-breakpoint: CPU 3 debug is powered down!
[    0.152000] hw-breakpoint: CPU 2 debug is powered down!
[    0.152000] hw-breakpoint: Debug register access (0xee113e95) caused undefined instruction on CPU 0
[    0.152000] hw-breakpoint: CPU 0 debug is powered down!
[    0.152000] Serial: AMBA PL011 UART driver
[    0.152000] uart-pl011.0: ttyAMA0 at MMIO 0xc00a1000 (irq = 7) is a PL011 rev3
[    0.156000] console [ttyAMA0] enabled
[    0.160000] uart-pl011.1: ttyAMA1 at MMIO 0xc00a0000 (irq = 6) is a PL011 rev3
[    0.176000] bio: create slab <bio-0> at 0
[    0.180000] gpiochip_add: registered GPIOs 0 to 31 on device: nxp-gpio.0
[    0.184000] gpiochip_add: registered GPIOs 32 to 63 on device: nxp-gpio.1
[    0.188000] gpiochip_add: registered GPIOs 64 to 95 on device: nxp-gpio.2
[    0.192000] gpiochip_add: registered GPIOs 96 to 127 on device: nxp-gpio.3
[    0.196000] gpiochip_add: registered GPIOs 128 to 159 on device: nxp-gpio.4
[    0.200000] gpiochip_add: registered GPIOs 160 to 167 on device: nxp-gpio.5
[    0.204000] pl08xdmac pl08xdmac.0: Unbalanced pm_runtime_enable!
[    0.208000] pl08xdmac pl08xdmac.0: initialized 8 virtual memcpy channels
[    0.212000] pl08xdmac pl08xdmac.0: initialized 16 virtual slave channels
[    0.216000] pl08xdmac pl08xdmac.0: DMA: PL080 rev1 at 0xc0000000 irq 1
[    0.220000] pl08xdmac pl08xdmac.1: Unbalanced pm_runtime_enable!
[    0.224000] pl08xdmac pl08xdmac.1: initialized 8 virtual memcpy channels
[    0.228000] pl08xdmac pl08xdmac.1: initialized 15 virtual slave channels
[    0.236000] pl08xdmac pl08xdmac.1: DMA: PL080 rev1 at 0xc0001000 irq 2
[    0.240000] fixed_vdds: 1350 mV 
[    0.244000] nxp_ion_probe success!!!
[    0.248000] SCSI subsystem initialized
[    0.252000] ssp-pl022 ssp-pl022.0: ARM PL022 driver, device ID: 0x00041022
[    0.256000] pl022: mapped registers from 0xc005b000 to f005b000
[    0.260000] ssp-pl022 ssp-pl022.0: setup for DMA on RX dma1chan7, TX dma1chan6
[    0.264000] ssp-pl022 ssp-pl022.0: will use autosuspend for runtime pm, delay 10ms
[    0.268000] usbcore: registered new interface driver usbfs
[    0.272000] usbcore: registered new interface driver hub
[    0.276000] usbcore: registered new device driver usb
[    0.280000] nxp-i2c.0:   390625 hz [pclk=200000000, clk = 256, scale= 1, timeout= 500 ms]
[    0.288000] nxp-i2c.1:    97656 hz [pclk=200000000, clk = 256, scale= 7, timeout= 500 ms]
[    0.292000] nxp-i2c.2:   195312 hz [pclk=200000000, clk = 256, scale= 3, timeout= 500 ms]
[    0.296000] Linux media interface: v0.10
[    0.300000] Linux video capture interface: v2.00
[    0.304000] pps_core: LinuxPPS API ver. 1 registered
[    0.308000] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.312000] PTP clock support registered
[    0.316000] Advanced Linux Sound Architecture Driver Version 1.0.25.
[    0.320000] Bluetooth: Core ver 2.16
[    0.324000] NET: Registered protocol family 31
[    0.328000] Bluetooth: HCI device and connection manager initialized
[    0.332000] Bluetooth: HCI socket layer initialized
[    0.336000] Bluetooth: L2CAP socket layer initialized
[    0.340000] Bluetooth: SCO socket layer initialized
[    0.344000] cfg80211: Calling CRDA to update world regulatory domain
[    0.344000] Switching to clocksource source timer
[    0.364000] NET: Registered protocol family 2
[    0.368000] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.376000] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.384000] TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
[    0.392000] TCP: Hash tables configured (established 131072 bind 65536)
[    0.400000] TCP: reno registered
[    0.404000] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.408000] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.416000] NET: Registered protocol family 1
[    0.420000] RPC: Registered named UNIX socket transport module.
[    0.424000] RPC: Registered udp transport module.
[    0.432000] RPC: Registered tcp transport module.
[    0.436000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.440000] Disply Reset Status : On
[    0.472000] find cec header!_edid_find_target_cec_address: cec physical address 1000
[    0.480000] hdmi_get_edid_preset: preferred_preset is supported
[    0.484000] Display HDMI register operation 
[    0.488000] Display.0 fps=161 (6 ms), wait= 4 jiffies, Pixelclk=200000000hz
[    0.496000] bt_bcm: rfkill initialized
[    0.500000] audit: initializing netlink socket (disabled)
[    0.508000] type=2000 audit(0.508:1): initialized
[    0.516000] NFS: Registering the id_resolver key type
[    0.524000] fuse init (API version 7.18)
[    0.528000] msgmni has been set to 1619
[    0.532000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[    0.540000] io scheduler noop registered
[    0.544000] io scheduler deadline registered
[    0.548000] io scheduler cfq registered (default)
[    0.552000] display.0 connected to fb.0  ...
[    0.556000] nxp-fb.0: dma addr = 0x74000000, buf[0xb30c8400]
[    0.564000] nxp-fb.0: dma addr = 0x74384000, buf[0xb30c85c0]
[    0.624000] hdmi_stop entered
[    0.628000] hdmi_run entered
[    0.640000] HDMI PHY Ready!!!
[    0.644000] Display.0 fps=161 (6 ms), wait= 4 jiffies, Pixelclk=200000000hz
[    0.648000] _calc_hdmi_sync_param: _h_sync_offset 0
[    0.680000] hdmi_run exit
[    0.680000] nxp-fb 0: out[0], 1280 * 720 - 32 bpp (phys:74000000 virt:0xb4000000 max:7372800)
[    0.696000] uart-pl011 uart-pl011.0: no DMA platform data
[    0.700000] uart-pl011 uart-pl011.1: no DMA platform data
[    0.708000] loop: module loaded
[    0.712000] tun: Universal TUN/TAP device driver, 1.6
[    0.716000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    0.724000] PPP generic driver version 2.4.2
[    0.728000] PPP BSD Compression module registered
[    0.732000] PPP Deflate Compression module registered
[    0.736000] PPP MPPE Compression module registered
[    0.740000] NET: Registered protocol family 24
[    0.748000] usbcore: registered new interface driver asix
[    0.752000] usbcore: registered new interface driver cdc_ether
[    0.756000] usbcore: registered new interface driver net1080
[    0.764000] usbcore: registered new interface driver cdc_subset
[    0.768000] usbcore: registered new interface driver zaurus
[    0.776000] usbcore: registered new interface driver cdc_ncm
[    0.780000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.788000] nxp-ehci nxp-ehci: SLsi Synopsys EHCI Host Controller
[    0.792000] nxp-ehci nxp-ehci: new USB bus registered, assigned bus number 1
[    0.800000] nxp-ehci nxp-ehci: irq 50, io mem 0xc0030000
[    0.816000] nxp-ehci nxp-ehci: USB 0.0 started, EHCI 1.00
[    0.820000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    0.828000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.832000] usb usb1: Product: SLsi Synopsys EHCI Host Controller
[    0.840000] usb usb1: Manufacturer: Linux 3.4.39-FriendlyARM ehci_hcd
[    0.848000] usb usb1: SerialNumber: nxp-ehci
[    0.852000] hub 1-0:1.0: USB hub found
[    0.856000] hub 1-0:1.0: 3 ports detected
[    0.860000] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[    1.064000] Core Release: 2.93a
[    1.068000] Setting default values for core params
[    1.072000] Finished setting default values for core params
[    1.276000] Using Descriptor DMA mode
[    1.280000] Dedicated Tx FIFOs mode
[    1.284000] dwc_otg dwc_otg: DWC OTG Controller
[    1.288000] dwc_otg dwc_otg: new USB bus registered, assigned bus number 2
[    1.296000] dwc_otg dwc_otg: irq 49, io mem 0x00000000
[    1.300000] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    1.308000] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.316000] usb usb2: Product: DWC OTG Controller
[    1.320000] usb usb2: Manufacturer: Linux 3.4.39-FriendlyARM dwc_otg_hcd
[    1.328000] usb usb2: SerialNumber: dwc_otg
[    1.332000] hub 2-0:1.0: USB hub found
[    1.336000] hub 2-0:1.0: 1 port detected
[    1.340000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.344000] nxp-ohci nxp-ohci: SLsi Synopsys OHCI Host Controller
[    1.352000] nxp-ohci nxp-ohci: new USB bus registered, assigned bus number 3
[    1.360000] nxp-ohci nxp-ohci: irq 50, io mem 0xc0020000
[    1.424000] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[    1.428000] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.436000] usb usb3: Product: SLsi Synopsys OHCI Host Controller
[    1.444000] HDMI HPD State 0x1
[    1.444000] usb usb3: Manufacturer: Linux 3.4.39-FriendlyARM ohci_hcd
[    1.452000] usb usb3: SerialNumber: nxp-ohci
[    1.456000] hub 3-0:1.0: USB hub found
[    1.460000] hub 3-0:1.0: 3 ports detected
[    1.464000] Initializing USB Mass Storage driver...
[    1.468000] usbcore: registered new interface driver usb-storage
[    1.476000] USB Mass Storage support registered.
[    1.480000] android_usb gadget: Mass Storage Function, version: 2009/09/11
[    1.488000] android_usb gadget: Number of LUNs=1
[    1.492000]  lun0: LUN: removable file: (no medium)
[    1.496000] find cec header!_edid_find_target_cec_address: cec physical address 1000
[    1.500000] android_usb gadget: android_usb ready
[    1.500000] mousedev: PS/2 mouse device common for all mice
[    1.500000] input: Nexell Keypad as /devices/platform/nxp-keypad/input/input0
[    1.500000] usbcore: registered new interface driver xpad
[    1.500000] input: ft5x0x_ts as /devices/virtual/input/input1
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:1)
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:2)
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:3)
[    1.508000] Error: i2c.2, addr:70, trans len:-11(1), try:3
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:1)
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:2)
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:3)
[    1.508000] Error: i2c.2, addr:70, trans len:-11(1), try:3
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:1)
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:2)
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:3)
[    1.508000] Error: i2c.2, addr:70, trans len:-11(1), try:3
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:1)
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:2)
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:3)
[    1.508000] Error: i2c.2, addr:70, trans len:-11(1), try:3
[    1.508000] read reg (0xa6) error, -11
[    1.508000] ft5x0x_ts 2-0038: chip not found
[    1.680000] _hdmi_hpd_changed: edid update success, preset 18
[    1.684000] notify_hpd_changed: state 1
[    1.688000] hdmi_run entered
[    1.692000] hdmi_run: hdmi already running!
[    1.720000] ft5x0x_ts 2-0038: probe ft5x0x TouchScreen failed, -11
[    1.724000] ft5x0x_ts: probe of 2-0038 failed with error -11
[    1.732000] [RTC] day=2009.09.01 time=00:00:00
[    1.736000] nxp-rtc nxp-rtc.0: rtc core: registered nxp-rtc as rtc0
[    1.740000] i2c /dev entries driver
[    1.744000] gspca_main: v2.14.0 registered
[    1.752000] usbcore: registered new interface driver uvcvideo
[    1.756000] USB Video Class driver (1.1.1)
[    1.760000] device-mapper: uevent: version 1.0.3
[    1.768000] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
[    1.776000] Bluetooth: HCI UART driver ver 2.2
[    1.780000] Bluetooth: HCI H4 protocol initialized
[    1.784000] DVFS: ASV[0] IDS(10mA, 10) Ro(110, 95)
[    1.788000] ASV  0 =  1400000khz,  1350000 uV 
[    1.792000] ASV  1 =  1200000khz,  1250000 uV 
[    1.796000] ASV  2 =  1000000khz,  1175000 uV 
[    1.804000] ASV  3 =   800000khz,  1125000 uV 
[    1.808000] ASV  4 =   700000khz,  1100000 uV 
[    1.812000] ASV  5 =   600000khz,  1075000 uV 
[    1.816000] ASV  6 =   500000khz,  1075000 uV 
[    1.820000] ASV  7 =   400000khz,  1075000 uV 
[    1.824000] DVFS: regulator vdd_arm_1.3V
[    1.828000] DVFS: cpu DVFS with PLL.1 [tables=8]
[    1.836000] cpuidle: using governor ladder
[    1.840000] cpuidle: using governor menu
[    1.844000] Synopsys Designware Multimedia Card Interface Driver
[    1.848000] dw_mmc dw_mmc.0: Using internal DMA controller.
[    1.856000] ------------[ cut here ]------------
[    1.856000] mmc0: no vmmc regulator found
[    1.856000] dw_mmc dw_mmc.0: Using external card detect irq 225 (io 161)
[    1.856000] dw_mmc dw_mmc.0: Version ID is 250a
[    1.856000] dw_mmc dw_mmc.0: DW MMC controller at irq 43, 32 bit host data width, 32 deep fifo hw timeout 500 ms
[    1.856000] dw_mmc dw_mmc.1: Using PIO mode.
[    1.856000] mmc1: no vmmc regulator found
[    1.856000] dw_mmc dw_mmc.1: Version ID is 250a
[    1.856000] dw_mmc dw_mmc.1: DW MMC controller at irq 44, 32 bit host data width, 32 deep fifo hw timeout 500 ms
[    1.856000] dw_mmc dw_mmc.2: Using internal DMA controller.
[    1.856000] mmc2: no vmmc regulator found
[    1.856000] dw_mmc dw_mmc.2: Using external card detect irq 152 (io 88)
[    1.856000] dw_mmc dw_mmc.2: Version ID is 250a
[    1.856000] dw_mmc dw_mmc.2: DW MMC controller at irq 45, 32 bit host data width, 32 deep fifo hw timeout 500 ms
[    1.860000] Registered led device: led1
[    1.860000] usbcore: registered new interface driver usbhid
[    1.860000] usbhid: USB HID core driver
[    1.860000] ADC: CHs 8, 200000(1000000 ~ 130208) sample rate, polling mode, scale=166(bit 6)
[    1.860000] snd pcm: register sound platform 'nxp-pcm'
[    1.860000] snd i2s: ch 0, master, iis mode, 48000(47999)hz, 32 FBITs, MCLK=12287980hz, RFS=256
[    1.860000] spdif-tx: 48000(47348)Hz, MCLK=12121212hz HDMI out
[    1.872000] ------------[ cut here ]------------
[    1.872000] WARNING: at lib/timerqueue.c:46 timerqueue_add+0xb8/0xc4()
[    1.872000] Modules linked in:
[    1.872000] [<800154ac>] (unwind_backtrace+0x0/0x12c) from [<800441a8>] (warn_slowpath_common+0x54/0x64)
[    1.872000] [<800441a8>] (warn_slowpath_common+0x54/0x64) from [<80044254>] (warn_slowpath_null+0x1c/0x24)
[    1.872000] [<80044254>] (warn_slowpath_null+0x1c/0x24) from [<80283d60>] (timerqueue_add+0xb8/0xc4)
[    1.872000] [<80283d60>] (timerqueue_add+0xb8/0xc4) from [<8006719c>] (enqueue_hrtimer+0x2c/0xc8)
[    1.872000] [<8006719c>] (enqueue_hrtimer+0x2c/0xc8) from [<8006776c>] (__run_hrtimer+0xc8/0x284)
[    1.872000] [<8006776c>] (__run_hrtimer+0xc8/0x284) from [<800684a0>] (hrtimer_interrupt+0x120/0x2a8)
[    1.872000] [<800684a0>] (hrtimer_interrupt+0x120/0x2a8) from [<80014870>] (twd_handler+0x34/0x44)
[    1.872000] [<80014870>] (twd_handler+0x34/0x44) from [<800bb0b0>] (handle_percpu_devid_irq+0x9c/0x190)
[    1.872000] [<800bb0b0>] (handle_percpu_devid_irq+0x9c/0x190) from [<800b78a0>] (generic_handle_irq+0x2c/0x44)
[    1.872000] [<800b78a0>] (generic_handle_irq+0x2c/0x44) from [<8000f5e4>] (handle_IRQ+0x58/0xb0)
[    1.872000] [<8000f5e4>] (handle_IRQ+0x58/0xb0) from [<80008538>] (gic_handle_irq+0x28/0x58)
[    1.872000] [<80008538>] (gic_handle_irq+0x28/0x58) from [<8000e940>] (__irq_svc+0x40/0x70)
[    1.872000] Exception stack(0xb3a4ddc8 to 0xb3a4de10)
[    1.872000] ddc0:                   00000004 00000004 00000008 00000001 b3a4de34 81353ec0
[    1.872000] dde0: 81353ec0 00a73000 81353ec8 00000003 00000001 000003e8 00000004 b3a4de10
[    1.872000] de00: 8001de54 80093a98 20000013 ffffffff
[    1.872000] [<8000e940>] (__irq_svc+0x40/0x70) from [<80093a98>] (generic_exec_single+0x78/0x90)
[    1.872000] [<80093a98>] (generic_exec_single+0x78/0x90) from [<80093bb8>] (smp_call_function_single+0x108/0x1e0)
[    1.872000] [<80093bb8>] (smp_call_function_single+0x108/0x1e0) from [<80014974>] (twd_cpufreq_transition+0x30/0x38)
[    1.872000] [<80014974>] (twd_cpufreq_transition+0x30/0x38) from [<800693a8>] (notifier_call_chain+0x44/0x84)
[    1.872000] [<800693a8>] (notifier_call_chain+0x44/0x84) from [<80069780>] (__srcu_notifier_call_chain+0x44/0x60)
[    1.872000] [<80069780>] (__srcu_notifier_call_chain+0x44/0x60) from [<800697b4>] (srcu_notifier_call_chain+0x18/0x20)
[    1.872000] [<800697b4>] (srcu_notifier_call_chain+0x18/0x20) from [<80458bdc>] (cpufreq_notify_transition+0xb8/0x28c)
[    1.872000] [<80458bdc>] (cpufreq_notify_transition+0xb8/0x28c) from [<80461568>] (nxp_cpufreq_change_frequency+0xd8/0x1cc)
[    1.872000] [<80461568>] (nxp_cpufreq_change_frequency+0xd8/0x1cc) from [<80461794>] (nxp_cpufreq_target+0x138/0x388)
[    1.872000] [<80461794>] (nxp_cpufreq_target+0x138/0x388) from [<8045fe04>] (cpufreq_interactive_speedchange_task+0x178/0x220)
[    1.872000] [<8045fe04>] (cpufreq_interactive_speedchange_task+0x178/0x220) from [<8006380c>] (kthread+0x90/0x94)
[    1.872000] [<8006380c>] (kthread+0x90/0x94) from [<8000f86c>] (kernel_thread_exit+0x0/0x8)
[    1.872000] ---[ end trace 35325b1b94c8d884 ]---
[    1.872000] hrtimer: interrupt took 365500 ns
[    1.904000] Internal error: Oops - undefined instruction: 0 [#1] PREEMPT SMP ARM
[    1.904000] Modules linked in:
[    1.904000] CPU: 2    Tainted: G        W     (3.4.39-FriendlyARM #1)
[    1.904000] PC is at 0x80000000
[    1.904000] LR is at gic_handle_irq+0x20/0x58
[    1.904000] pc : [<80000000>]    lr : [<80008530>]    psr: 80000193
[    1.904000] sp : b3a4ddb8  ip : 0000000d  fp : 00000050
[    1.904000] r10: 00000001  r9 : 00000003  r8 : 00e80010
[    1.904000] r7 : b3a4ddfc  r6 : b3a4ddc8  r5 : f0300100  r4 : 0000011d
[    1.904000] r3 : 808e020c  r2 : 00000010  r1 : 0000001d  r0 : 0000011d
[    1.904000] Flags: Nzcv  IRQs off  FIQs on  Mode SVC_32  ISA ARM  Segment kernel
[    1.904000] Control: 10c5387d  Table: 4000404a  DAC: 00000015
[    1.904000] 
[    1.904000] LR: 0x800084b0:
[    1.904000] 84b0  e28dd088 e8bd81f0 e30b0ae4 e594100c e1a02005 e1a03007 e348007a eb193ba4
[    1.904000] 84d0  e5946004 e3a0c000 e594e008 e3070540 e1a01008 e1a03005 e58dc000 e348007b
[    1.904000] 84f0  e28d2008 e58d7014 e58d6008 e58de010 e58dc00c eb0029cb eaffffe8 80901a0c
[    1.904000] 8510  e92d4070 e3074cc8 e348408f e1a06000 e5945004 ea000003 e594058c eb02cd48
[    1.904000] 8530  e1a01006 eb001c14 e595200c e3c20b07 e240c010 e1a01000 e35c0ffb 9afffff5
[    1.904000] 8550  e350000f 88bd8070 e5852010 e1a01006 eb002e82 eafffff3 e92d41f0 e304737c
[    1.904000] 8570  e3487095 e1a04000 e5972048 e3520000 d8bd81f0 e59f806c e3a06000 e1a05006
[    1.904000] 8590  e5183020 e5933000 e3530000 0a00000c e2631000 e5980000 e0033001 e16f1f13
[    1.904000] 
[    1.904000] SP: 0xb3a4dd38:
[    1.904000] dd38  717cc116 00000000 717cbf22 00000000 00000021 00000001 b3800d80 80000004
[    1.904000] dd58  80000193 b3a4c050 00000001 00000f00 8000e9ec 8000e9ec 0000011d 0000001d
[    1.904000] dd78  00000010 808e020c 0000011d f0300100 b3a4ddc8 b3a4ddfc 00e80010 00000003
[    1.904000] dd98  00000001 00000050 0000000d b3a4ddb8 80008530 80000000 80000193 ffffffff
[    1.904000] ddb8  80093a94 20000013 ffffffff 8000e940 00000004 00000004 00000008 00000001
[    1.904000] ddd8  b3a4de34 81353ec0 81353ec0 00a73000 81353ec8 00000003 00000001 000003e8
[    1.904000] ddf8  00000004 b3a4de10 8001de54 80093a94 20000013 ffffffff 00000000 00000003
[    1.904000] de18  80014880 00000000 00000001 80662490 00000000 80093bb8 00000000 81353ec0
[    1.904000] 
[    1.904000] R3: 0x808e018c:
[    1.904000] 018c  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    1.904000] 01ac  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    1.904000] 01cc  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    1.904000] 01ec  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    1.904000] 020c  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    1.904000] 022c  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    1.904000] 024c  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    1.904000] 026c  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    1.904000] 
[    1.904000] R5: 0xf0300080:
[    1.904000] 0080  0000000b 000055f3 00000000 00000000 00000000 00000000 00000000 00000000
[    1.904000] 00a0  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    1.904000] 00c0  c0000000 cff00000 00000000 00000000 0000000f 000000ff 00000000 00000000
[    1.904000] 00e0  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    1.904000] 0100  00000001 000000f0 00000002 000003ff 00000000 000000a0 000003ff 00000003
[    1.904000] 0120  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    1.904000] 0140  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    1.904000] 0160  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    1.904000] 
[    1.904000] R6: 0xb3a4dd48:
[    1.904000] dd48  00000021 00000001 b3800d80 80000004 80000193 b3a4c050 00000001 00000f00
[    1.904000] dd68  8000e9ec 8000e9ec 0000011d 0000001d 00000010 808e020c 0000011d f0300100
[    1.904000] dd88  b3a4ddc8 b3a4ddfc 00e80010 00000003 00000001 00000050 0000000d b3a4ddb8
[    1.904000] dda8  80008530 80000000 80000193 ffffffff 80093a94 20000013 ffffffff 8000e940
[    1.904000] ddc8  00000004 00000004 00000008 00000001 b3a4de34 81353ec0 81353ec0 00a73000
[    1.904000] dde8  81353ec8 00000003 00000001 000003e8 00000004 b3a4de10 8001de54 80093a94
[    1.904000] de08  20000013 ffffffff 00000000 00000003 80014880 00000000 00000001 80662490
[    1.904000] de28  00000000 80093bb8 00000000 81353ec0 81353ec0 80014880 00000000 00000001
[    1.904000] 
[    1.904000] R7: 0xb3a4dd7c:
[    1.904000] dd7c  808e020c 0000011d f0300100 b3a4ddc8 b3a4ddfc 00e80010 00000003 00000001
[    1.904000] dd9c  00000050 0000000d b3a4ddb8 80008530 80000000 80000193 ffffffff 80093a94
[    1.904000] ddbc  20000013 ffffffff 8000e940 00000004 00000004 00000008 00000001 b3a4de34
[    1.904000] dddc  81353ec0 81353ec0 00a73000 81353ec8 00000003 00000001 000003e8 00000004
[    1.904000] ddfc  b3a4de10 8001de54 80093a94 20000013 ffffffff 00000000 00000003 80014880
[    1.904000] de1c  00000000 00000001 80662490 00000000 80093bb8 00000000 81353ec0 81353ec0
[    1.904000] de3c  80014880 00000000 00000001 80a28c48 ffffffff b3a4df50 00000001 80930630
[    1.904000] de5c  00000000 00000000 80014974 80014944 800693a8 ffffffff 80a28c48 80a28c30
[    1.904000] Process cfinteractive (pid: 33, stack limit = 0xb3a4c2f0)
[    1.904000] Stack: (0xb3a4ddb8 to 0xb3a4e000)
[    1.904000] dda0:                                                       80093a94 20000013
[    1.904000] ddc0: ffffffff 8000e940 00000004 00000004 00000008 00000001 b3a4de34 81353ec0
[    1.904000] dde0: 81353ec0 00a73000 81353ec8 00000003 00000001 000003e8 00000004 b3a4de10
[    1.904000] de00: 8001de54 80093a94 20000013 ffffffff 00000000 00000003 80014880 00000000
[    1.904000] de20: 00000001 80662490 00000000 80093bb8 00000000 81353ec0 81353ec0 80014880
[    1.904000] de40: 00000000 00000001 80a28c48 ffffffff b3a4df50 00000001 80930630 00000000
[    1.904000] de60: 00000000 80014974 80014944 800693a8 ffffffff 80a28c48 80a28c30 00000000
[    1.904000] de80: ffffffff b3a4df50 00000001 80069780 00000000 10624dd3 b3a4df50 00000003
[    1.904000] dea0: 00000001 00155cc0 b3981d80 80a28c30 10624dd3 800697b4 00000000 808f8b1c
[    1.904000] dec0: b314d60c 80458bdc 00000003 b3a4df50 808f8b1c b314d60c b314d600 00155cc0
[    1.904000] dee0: 00000001 80461568 ffffffff b314d600 8094c578 b3981d80 b314d620 b3130c80
[    1.904000] df00: 00155cc0 b314d600 8094c578 b3981d80 b314d620 b3130c80 00155cc0 10624dd3
[    1.904000] df20: 000003e8 80461794 00000003 00000001 b3848424 00000000 00000001 b3848424
[    1.904000] df40: 15b23300 00000000 00000000 00000000 00000003 00124f80 00155cc0 80072a01
[    1.904000] df60: 8133b488 8133b3d8 00000000 808f8b1c 8133b488 808e03d8 00155cc0 808f90c8
[    1.904000] df80: b3a4df9c 8045fe04 b3843f54 808e03d8 b3a4c008 80a28ca0 00000000 00000001
[    1.904000] dfa0: 00000001 b3843f44 00000000 8045fc8c 00000013 00000000 00000000 00000000
[    1.904000] dfc0: 00000000 8006380c 8000f86c 00000000 00000000 00000000 00000000 00000000
[    1.904000] dfe0: b3a4dfe0 b3a4dfe0 b3843f44 8006377c 8000f86c 8000f86c ffffffff ffffffff
[    1.904000] [<80008530>] (gic_handle_irq+0x20/0x58) from [<8000e940>] (__irq_svc+0x40/0x70)
[    1.904000] Exception stack(0xb3a4ddc8 to 0xb3a4de10)
[    1.904000] ddc0:                   00000004 00000004 00000008 00000001 b3a4de34 81353ec0
[    1.904000] dde0: 81353ec0 00a73000 81353ec8 00000003 00000001 000003e8 00000004 b3a4de10
[    1.904000] de00: 8001de54 80093a94 20000013 ffffffff
[    1.904000] [<8000e940>] (__irq_svc+0x40/0x70) from [<80093a94>] (generic_exec_single+0x74/0x90)
[    1.904000] [<80093a94>] (generic_exec_single+0x74/0x90) from [<80093bb8>] (smp_call_function_single+0x108/0x1e0)
[    1.904000] [<80093bb8>] (smp_call_function_single+0x108/0x1e0) from [<80014974>] (twd_cpufreq_transition+0x30/0x38)
[    1.904000] [<80014974>] (twd_cpufreq_transition+0x30/0x38) from [<800693a8>] (notifier_call_chain+0x44/0x84)
[    1.904000] [<800693a8>] (notifier_call_chain+0x44/0x84) from [<80069780>] (__srcu_notifier_call_chain+0x44/0x60)
[    1.904000] [<80069780>] (__srcu_notifier_call_chain+0x44/0x60) from [<800697b4>] (srcu_notifier_call_chain+0x18/0x20)
[    1.904000] [<800697b4>] (srcu_notifier_call_chain+0x18/0x20) from [<80458bdc>] (cpufreq_notify_transition+0xb8/0x28c)
[    1.904000] [<80458bdc>] (cpufreq_notify_transition+0xb8/0x28c) from [<80461568>] (nxp_cpufreq_change_frequency+0xd8/0x1cc)
[    1.904000] [<80461568>] (nxp_cpufreq_change_frequency+0xd8/0x1cc) from [<80461794>] (nxp_cpufreq_target+0x138/0x388)
[    1.904000] [<80461794>] (nxp_cpufreq_target+0x138/0x388) from [<8045fe04>] (cpufreq_interactive_speedchange_task+0x178/0x220)
[    1.904000] [<8045fe04>] (cpufreq_interactive_speedchange_task+0x178/0x220) from [<8006380c>] (kthread+0x90/0x94)
[    1.904000] [<8006380c>] (kthread+0x90/0x94) from [<8000f86c>] (kernel_thread_exit+0x0/0x8)
[    1.904000] Code: bad PC value
[    1.904000] ---[ end trace 35325b1b94c8d885 ]---
[    1.904000] BUG: sleeping function called from invalid context at kernel/rwsem.c:20
[    1.904000] in_atomic(): 1, irqs_disabled(): 0, pid: 33, name: cfinteractive
[    1.904000] [<800154ac>] (unwind_backtrace+0x0/0x12c) from [<8065bfc4>] (down_read+0x1c/0x28)
[    1.904000] [<8065bfc4>] (down_read+0x1c/0x28) from [<80056dc4>] (exit_signals+0x18/0x13c)
[    1.904000] [<80056dc4>] (exit_signals+0x18/0x13c) from [<800484a4>] (do_exit+0x98/0x7dc)
[    1.904000] [<800484a4>] (do_exit+0x98/0x7dc) from [<80012b88>] (die+0x140/0x1f0)
[    1.904000] [<80012b88>] (die+0x140/0x1f0) from [<800082a8>] (do_undefinstr+0xa4/0x1d0)
[    1.904000] [<800082a8>] (do_undefinstr+0xa4/0x1d0) from [<8000e9ec>] (__und_svc_finish+0x0/0x14)
[    1.904000] Exception stack(0xb3a4dd70 to 0xb3a4ddb8)
[    1.904000] dd60:                                     0000011d 0000001d 00000010 808e020c
[    1.904000] dd80: 0000011d f0300100 b3a4ddc8 b3a4ddfc 00e80010 00000003 00000001 00000050
[    1.904000] dda0: 0000000d b3a4ddb8 80008530 80000000 80000193 ffffffff
[    1.904000] [<8000e9ec>] (__und_svc_finish+0x0/0x14) from [<80000000>] (0x80000000)
[    1.904000] note: cfinteractive[33] exited with preempt_count 1
[    3.180000] WARNING: at kernel/sched/core.c:3222 _raw_spin_unlock_irqrestore+0x24/0x44()
[    3.188000] Modules linked in:
[    3.192000] [<800154ac>] (unwind_backtrace+0x0/0x12c) from [<800441a8>] (warn_slowpath_common+0x54/0x64)
[    3.200000] [<800441a8>] (warn_slowpath_common+0x54/0x64) from [<80044254>] (warn_slowpath_null+0x1c/0x24)
[    3.212000] [<80044254>] (warn_slowpath_null+0x1c/0x24) from [<8065db6c>] (_raw_spin_unlock_irqrestore+0x24/0x44)
[    3.220000] [<8065db6c>] (_raw_spin_unlock_irqrestore+0x24/0x44) from [<800be878>] (force_quiescent_state+0x10c/0x380)
[    3.232000] [<800be878>] (force_quiescent_state+0x10c/0x380) from [<800c0338>] (__rcu_process_callbacks+0x360/0x3c4)
[    3.244000] [<800c0338>] (__rcu_process_callbacks+0x360/0x3c4) from [<800c040c>] (rcu_process_callbacks+0x70/0x160)
[    3.252000] [<800c040c>] (rcu_process_callbacks+0x70/0x160) from [<8004ade0>] (__do_softirq+0xc4/0x22c)
[    3.264000] [<8004ade0>] (__do_softirq+0xc4/0x22c) from [<8004b3cc>] (irq_exit+0x90/0x94)
[    3.272000] [<8004b3cc>] (irq_exit+0x90/0x94) from [<8000f5ec>] (handle_IRQ+0x60/0xb0)
[    3.280000] [<8000f5ec>] (handle_IRQ+0x60/0xb0) from [<80008538>] (gic_handle_irq+0x28/0x58)
[    3.288000] [<80008538>] (gic_handle_irq+0x28/0x58) from [<8000e940>] (__irq_svc+0x40/0x70)
[    3.296000] Exception stack(0xb38a1f88 to 0xb38a1fd0)
[    3.300000] 1f80:                   ffffffed 00000003 00a73000 00000000 80953e88 80662490
[    3.308000] 1fa0: b38a0000 b38a0000 80900ed8 b38a0018 b38a0000 00000000 01000000 b38a1fd0
[    3.316000] 1fc0: 8000f92c 8000f930 60000013 ffffffff
[    3.320000] [<8000e940>] (__irq_svc+0x40/0x70) from [<8000f930>] (default_idle+0x2c/0x30)
[    3.328000] [<8000f930>] (default_idle+0x2c/0x30) from [<8000fc8c>] (cpu_idle+0xdc/0x108)
[    3.336000] [<8000fc8c>] (cpu_idle+0xdc/0x108) from [<40008168>] (0x40008168)
[    3.344000] ---[ end trace 35325b1b94c8d886 ]---
[    3.348000] Unable to handle kernel paging request at virtual address e3a0000c
[    3.356000] pgd = 80004000
[    3.360000] [e3a0000c] *pgd=00000000
[    3.364000] Internal error: Oops: 5 [#2] PREEMPT SMP ARM
[    3.368000] Modules linked in:
[    3.372000] CPU: 3    Tainted: G      D W     (3.4.39-FriendlyARM #1)
[    3.376000] PC is at rcu_process_gp_end.isra.21+0x14/0x98
[    3.384000] LR is at __rcu_process_callbacks+0x40/0x3c4
[    3.388000] pc : [<800bfd94>]    lr : [<800c0018>]    psr: 60000193
[    3.388000] sp : b38a1ec0  ip : 00000000  fp : 80251b20
[    3.400000] r10: 8094201c  r9 : 00000102  r8 : 00000024
[    3.404000] r7 : 808dec30  r6 : 60000113  r5 : e3a00000  r4 : 808deb20
[    3.412000] r3 : 809421e8  r2 : eb00a0ae  r1 : 8095ec80  r0 : 80251b20
[    3.416000] Flags: nZCv  IRQs off  FIQs on  Mode SVC_32  ISA ARM  Segment kernel
[    3.424000] Control: 10c5387d  Table: 4000404a  DAC: 00000015
[    3.432000] 
[    3.432000] PC: 0x800bfd14:
[    3.436000] fd14  e1953f9f e2433001 e1852f93 e3320000 1afffffa f57ff05f e3530000 1a000001
[    3.444000] fd34  e2840014 ebfeb872 e59f0014 eb16721c e59f0008 e8bd4070 ea166f35 e7f001f2
[    3.452000] fd54  8090e9ec 809dc18c e30f0fa8 e348000b eaffffcd e30f0f98 e348000b eaffffca
[    3.460000] fd74  e30f0fb8 e348000b eaffffc7 e92d4070 e10f6000 f10c0080 e5905010 e5902000
[    3.468000] fd94  e595300c e1520003 0a000004 e1a04000 e1a00005 eb167824 e3500000 1a000001
[    3.476000] fdb4  e121f006 e8bd8070 e5942000 e595300c e1520003 0a00000e e2841020 e891000e
[    3.484000] fdd4  e5843024 e584101c e5842020 e5943004 e595200c e0623003 e5842000 e3530000
[    3.492000] fdf4  e5943014 b5842004 e5952010 e0133002 05c4300d e1a00005 e1a01006 e8bd4070
[    3.500000] 
[    3.500000] LR: 0x800bff98:
[    3.504000] ff98  e30e26c0 e3a03000 e3482090 eaffff9b e59f2004 e3a03000 eaffff98 8090e7c0
[    3.512000] ffb8  e59f2004 e3a03000 eaffff94 8090e8c0 e59f2004 e3a03001 eaffff90 8090e8c0
[    3.520000] ffd8  e92d4ff0 e1a0b001 e5d1300e e24dd00c e1a05000 e3530000 0a0000d1 e30420c0
[    3.528000] fff8  e59530dc e348208e e5922000 e0623003 e3530000 ba0000c6 e1a0000b ebffff59
[    3.536000] 0018  e1a00005 e1a0100b ebfffceb e3500000 1a000005 e5db300d e3530000 0a000002
[    3.544000] 0038  e5db300c e3530000 1a0000a9 e59b3000 e59520c8 e1530002 13a0301c 03a03018
[    3.556000] 0058  e08b3003 e5933004 e5933000 e3530000 0a000003 e59520c8 e59530c4 e1520003
[    3.564000] 0078  0a000095 e59b301c e28b9018 e1590003 0a000034 e3083b4c e348308f e5933004
[    3.572000] 
[    3.572000] SP: 0xb38a1e40:
[    3.576000] 1e40  00000c96 00000000 00000009 8065db6c 00000c96 807b3eb0 00000102 8094201c
[    3.584000] 1e60  800bfd94 60000193 ffffffff b38a1eac 00000024 8000e8d8 80251b20 8095ec80
[    3.592000] 1e80  eb00a0ae 809421e8 808deb20 e3a00000 60000113 808dec30 00000024 00000102
[    3.600000] 1ea0  8094201c 80251b20 00000000 b38a1ec0 800c0018 800bfd94 60000193 ffffffff
[    3.608000] 1ec0  808deb20 8090e8c0 809421e8 800c0018 6edd5900 00200200 ffffffff 808deb20
[    3.616000] 1ee0  808f90c8 809421e8 808dec30 00000024 00000102 8094201c 00000000 800c040c
[    3.624000] 1f00  800c039c 00000009 00000001 808e40a4 b38a0018 8004ade0 808f17c0 b38a0038
[    3.632000] 1f20  00000003 808de978 8097f600 0000000a 000001c3 b38a0018 808f90c8 b38a0000
[    3.640000] 
[    3.640000] FP: 0x80251aa0:
[    3.644000] 1aa0  e1160009 1affffbf e1e0300c e1e01006 e7eb3053 e7eb1051 e2833001 e2811001
[    3.652000] 1ac0  eaffffc4 e066600c e0623003 e1836006 e2840010 ebfff7c4 e3560000 e5840004
[    3.660000] 1ae0  e584000c 0affffea e5943034 e284001c e3833008 e5843034 ebfff7bb e584000c
[    3.668000] 1b00  eaffffe3 e5946028 e2840010 ebfff7b6 e5942018 e1a01000 e5840004 e1a00006
[    3.676000] 1b20  eb00a0ae e5940004 ebf72a66 e5943034 e3a00000 e5846004 e584600c e3130001
[    3.684000] 1b40  01a05000 0affffd2 e30f6c9c e5943004 e348608f e307e140 e5961000 e348e0a0
[    3.692000] 1b60  e28324c0 e59e7000 e7eb3053 e594c00c e1a05000 e1a01621 e5843004 e28c34c0
[    3.700000] 1b80  e0612622 e7ebc05c e584c00c e1a00005 e1a01282 e0812102 e0872002 e5842000
[    3.708000] 
[    3.708000] R0: 0x80251aa0:
[    3.716000] 1aa0  e1160009 1affffbf e1e0300c e1e01006 e7eb3053 e7eb1051 e2833001 e2811001
[    3.724000] 1ac0  eaffffc4 e066600c e0623003 e1836006 e2840010 ebfff7c4 e3560000 e5840004
[    3.732000] 1ae0  e584000c 0affffea e5943034 e284001c e3833008 e5843034 ebfff7bb e584000c
[    3.740000] 1b00  eaffffe3 e5946028 e2840010 ebfff7b6 e5942018 e1a01000 e5840004 e1a00006
[    3.748000] 1b20  eb00a0ae e5940004 ebf72a66 e5943034 e3a00000 e5846004 e584600c e3130001
[    3.756000] 1b40  01a05000 0affffd2 e30f6c9c e5943004 e348608f e307e140 e5961000 e348e0a0
[    3.764000] 1b60  e28324c0 e59e7000 e7eb3053 e594c00c e1a05000 e1a01621 e5843004 e28c34c0
[    3.772000] 1b80  e0612622 e7ebc05c e584c00c e1a00005 e1a01282 e0812102 e0872002 e5842000
[    3.780000] 
[    3.780000] R1: 0x8095ec00:
[    3.784000] ec00  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    3.792000] ec20  00000000 00000000 0000000b 00000000 00000000 00000000 00000000 00000000
[    3.800000] ec40  b3803200 00000000 00000000 00000000 b3803300 b3803380 0000329d b3803400
[    3.808000] ec60  b3803280 00000036 00000052 b3802280 b3802180 00000000 00000000 00000000
[    3.816000] ec80  00000280 00000000 94c8d886 35325b1b 00000000 00000000 00000000 00000000
[    3.824000] eca0  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    3.832000] ecc0  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    3.840000] ece0  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    3.848000] 
[    3.848000] R2: 0xeb00a02e:
[    3.852000] a02c  ******** ******** ******** ******** ******** ******** ******** ********
[    3.860000] a04c  ******** ******** ******** ******** ******** ******** ******** ********
[    3.868000] a06c  ******** ******** ******** ******** ******** ******** ******** ********
[    3.880000] a08c  ******** ******** ******** ******** ******** ******** ******** ********
[    3.888000] a0ac  ******** ******** ******** ******** ******** ******** ******** ********
[    3.896000] a0cc  ******** ******** ******** ******** ******** ******** ******** ********
[    3.904000] a0ec  ******** ******** ******** ******** ******** ******** ******** ********
[    3.912000] a10c  ******** ******** ******** ******** ******** ******** ******** ********
[    3.920000] a12c  ******** ******** ******** ******** ******** ******** ******** ********
[    3.928000] 
[    3.928000] R3: 0x80942168:
[    3.932000] 2168  00000000 00000000 808458d8 00000000 00000000 00000000 00000000 808458c8
[    3.940000] 2188  00000000 00000000 00000000 00000000 80845930 00000000 00000000 00000000
[    3.948000] 21a8  00000000 80845918 00000000 00000000 00000000 00000000 80845900 00000000
[    3.956000] 21c8  00000000 00000000 00000000 808458e8 00000000 00000000 00000000 00000000
[    3.964000] 21e8  80845948 00000000 00000000 00000000 00000000 80845a54 00000000 00000000
[    3.972000] 2208  00000000 00000000 80845a78 00000000 00000000 00000000 00000000 80845a40
[    3.980000] 2228  00000000 00000000 00000000 00000000 80845a08 00000000 00000000 00000000
[    3.988000] 2248  00000000 80845958 00000000 00000000 00000000 00000000 80845a64 00000000
[    3.996000] 
[    3.996000] R4: 0x808deaa0:
[    4.000000] eaa0  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    4.008000] eac0  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    4.016000] eae0  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    4.024000] eb00  00000000 00000000 00000000 00000000 00000000 01400000 00000000 00000001
[    4.032000] eb20  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    4.044000] eb40  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    4.052000] eb60  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    4.060000] eb80  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    4.068000] 
[    4.068000] R5: 0xe39fff80:
[    4.072000] ff80  ******** ******** ******** ******** ******** ******** ******** ********
[    4.080000] ffa0  ******** ******** ******** ******** ******** ******** ******** ********
[    4.088000] ffc0  ******** ******** ******** ******** ******** ******** ******** ********
[    4.096000] ffe0  ******** ******** ******** ******** ******** ******** ******** ********
[    4.104000] 0000  ******** ******** ******** ******** ******** ******** ******** ********
[    4.112000] 0020  ******** ******** ******** ******** ******** ******** ******** ********
[    4.120000] 0040  ******** ******** ******** ******** ******** ******** ******** ********
[    4.128000] 0060  ******** ******** ******** ******** ******** ******** ******** ********
[    4.136000] 
[    4.136000] R7: 0x808debb0:
[    4.140000] ebb0  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    4.148000] ebd0  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    4.156000] ebf0  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    4.164000] ec10  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    4.172000] ec30  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    4.180000] ec50  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    4.188000] ec70  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    4.196000] ec90  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    4.208000] 
[    4.208000] R10: 0x80941f9c:
[    4.212000] 1f9c  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    4.220000] 1fbc  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    4.228000] 1fdc  00000000 8084578c 00000000 00000000 00000000 00000000 80845780 00000000
[    4.236000] 1ffc  00000000 00000000 00000000 8084579c 00000000 00000000 00000000 00000000
[    4.244000] 201c  808457c4 00000000 00000000 00000000 00000000 808457b4 00000000 00000000
[    4.252000] 203c  00000000 00000000 808457a4 00000000 00000000 00000000 00000000 808457d4
[    4.260000] 205c  00000000 00000000 00000000 00000000 808457e8 00000000 00000000 00000000
[    4.268000] 207c  00000000 80845878 00000000 00000000 00000000 00000000 808458bc 00000000
[    4.276000] Process swapper/3 (pid: 0, stack limit = 0xb38a02f0)
[    4.280000] Stack: (0xb38a1ec0 to 0xb38a2000)
[    4.288000] 1ec0: 808deb20 8090e8c0 809421e8 800c0018 6edd5900 00200200 ffffffff 808deb20
[    4.296000] 1ee0: 808f90c8 809421e8 808dec30 00000024 00000102 8094201c 00000000 800c040c
[    4.304000] 1f00: 800c039c 00000009 00000001 808e40a4 b38a0018 8004ade0 808f17c0 b38a0038
[    4.312000] 1f20: 00000003 808de978 8097f600 0000000a 000001c3 b38a0018 808f90c8 b38a0000
[    4.320000] 1f40: 00000000 0000011d b38a0018 b38a0000 00000000 8004b3cc 808e020c 8000f5ec
[    4.328000] 1f60: 808f7cc8 f0300100 b38a1f88 b38a1fbc 80900ed8 80008538 8000f930 60000013
[    4.336000] 1f80: ffffffff 8000e940 ffffffed 00000003 00a73000 00000000 80953e88 80662490
[    4.344000] 1fa0: b38a0000 b38a0000 80900ed8 b38a0018 b38a0000 00000000 01000000 b38a1fd0
[    4.352000] 1fc0: 8000f92c 8000f930 60000013 ffffffff 8000f904 8000fc8c 7385406a 00000015
[    4.360000] 1fe0: 10c0387d 80954140 4000406a 413fc090 00000000 40008168 ffffffff ffffffff
[    4.368000] [<800bfd94>] (rcu_process_gp_end.isra.21+0x14/0x98) from [<800c0018>] (__rcu_process_callbacks+0x40/0x3c4)
[    4.380000] [<800c0018>] (__rcu_process_callbacks+0x40/0x3c4) from [<800c040c>] (rcu_process_callbacks+0x70/0x160)
[    4.388000] [<800c040c>] (rcu_process_callbacks+0x70/0x160) from [<8004ade0>] (__do_softirq+0xc4/0x22c)
[    4.400000] [<8004ade0>] (__do_softirq+0xc4/0x22c) from [<8004b3cc>] (irq_exit+0x90/0x94)
[    4.408000] [<8004b3cc>] (irq_exit+0x90/0x94) from [<8000f5ec>] (handle_IRQ+0x60/0xb0)
[    4.416000] [<8000f5ec>] (handle_IRQ+0x60/0xb0) from [<80008538>] (gic_handle_irq+0x28/0x58)
[    4.424000] [<80008538>] (gic_handle_irq+0x28/0x58) from [<8000e940>] (__irq_svc+0x40/0x70)
[    4.432000] Exception stack(0xb38a1f88 to 0xb38a1fd0)
[    4.436000] 1f80:                   ffffffed 00000003 00a73000 00000000 80953e88 80662490
[    4.444000] 1fa0: b38a0000 b38a0000 80900ed8 b38a0018 b38a0000 00000000 01000000 b38a1fd0
[    4.452000] 1fc0: 8000f92c 8000f930 60000013 ffffffff
[    4.456000] [<8000e940>] (__irq_svc+0x40/0x70) from [<8000f930>] (default_idle+0x2c/0x30)
[    4.464000] [<8000f930>] (default_idle+0x2c/0x30) from [<8000fc8c>] (cpu_idle+0xdc/0x108)
[    4.472000] [<8000fc8c>] (cpu_idle+0xdc/0x108) from [<40008168>] (0x40008168)
[    4.480000] Code: e10f6000 f10c0080 e5905010 e5902000 (e595300c) 
[    4.488000] ---[ end trace 35325b1b94c8d887 ]---
[    4.492000] Kernel panic - not syncing: Fatal exception in interrupt
[    4.496000] ------------[ cut he
--------------------------------------------------------------------------------
 Second Boot by Nexell Co. : Built on Nov 19 2014 20:10:38
--------------------------------------------------------------------------------
 PLL0: 550000000   PLL1: 1200000000   PLL2: 800000000   PLL3: 612000000

 Divider0 PLL: 1 CPU:1200000000   CPU BUS:300000000
 Divider1 PLL: 2 BCLK:400000000   PCLK:200000000
 Divider2 PLL: 2 MDCLK:800000000   MCLK:800000000   
		 MBCLK:400000000   MPCLK:200000000
 Divider3 PLL: 0 G3D BCLK:550000000
 Divider4 PLL: 2 MPEG BCLK:400000000   MPEG PCLK:200000000

123
DDR3 POR Init Start
phy init

########## READ/GATE Level ##########
DDR3 Init Done!
Loading from sdmmc...
 Image Loading Done!
Launch to 0x42C00000


U-Boot 2014.07-gd46d757 (Nov 27 2015 - 17:09:12)

PLL : [0] =  550000000, [1] = 1200000000, [2] =  800000000, [3] =  614399000
PLL1: CPU FCLK = 1200000000, HCLK = 300000000
PLL2: BUS BCLK =  400000000, PCLK = 200000000
PLL2: MEM MCLK =  800000000, DCLK = 800000000, BCLK = 400000000, PCLK = 200000000
PLL0: G3D BCLK =  550000000
PLL2: MPG BCLK =  400000000, PCLK = 200000000
I2C:   ready
DRAM:  256 MiB
Heap = 0x43000000~0x45000000
Code = 0x42c00000~0x42c72984
GLD  = 0x42bffeb8
GLBD = 0x42bffe68
SP   = 0x42bffe68,0x42bffe50(CURR)
PC   = 0x42c06114
TAGS = 0x40000100 
PAGE = 0x42c80000~0x42c8c000
MACH = [4330]   
VER  = 1      
BOARD= [nanopi2]    
LCD  = N/A (-1)
MMC:   NXP DWMMC: 0, NXP DWMMC: 1, NXP DWMMC: 2
In:    serial
Out:   serial
Err:   serial
switch to partitions #0, OK
mmc0 is current device
Writing to MMC(0)... done
HDMI: display.0, preset 0 (1280 *  720)
HDMI: PHY Ready!!!
DONE: Logo bmp 800 by 480 (3bpp), len=1152056 

DRAW: 0x47000000 -> 0x46000000 

Hit any key to stop autoboot:  1  0 
## Booting kernel from Legacy Image at 48000000 ...
   Image Name:   Linux-3.4.39-FriendlyARM
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4767712 Bytes = 4.5 MiB
   Load Address: 40008000
   Entry Point:  40008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 3.4.39-FriendlyARM (root@jensen) (gcc version 4.9.3 (ctng-1.21.0-229g-FA) ) #1 SMP PREEMPT Sat Nov 28 17:36:10 HKT 2015
[    0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine: NANOPI2
[    0.000000] Display: HDMI selected
[    0.000000] nxp_reserve_mem: reserve CMA: size 201326592
[    0.000000] NXP/CMA: Reserved 0x74000000/0x0c000000 for 'ion'
[    0.000000] NXP/CMA: success register cma region for 'ion'
[    0.000000] Memory policy: ECC disabled, Data cache writealloc
[    0.000000] CPU : iomap[ 0]: p 0xc0000000 -> v 0xf0000000 len=0x300000
[    0.000000] CPU : iomap[ 1]: p 0xf0000000 -> v 0xf0300000 len=0x100000
[    0.000000] CPU : iomap[ 2]: p 0xcf000000 -> v 0xf0400000 len=0x100000
[    0.000000] CPU : iomap[ 3]: p 0x2c000000 -> v 0xf0500000 len=0x100000
[    0.000000] CPU : iomap[ 4]: p 0x00000000 -> v 0xf0600000 len=0x100000
[    0.000000] CPU : DMA Zone Size =16M, CORE 4
[    0.000000] CPU : VERSION = 2 (0xE153000A), Assign Peripheral Exclusive Bus
[    0.000000] s5p4418-NanoPi2: Board initialized
[    0.000000] CPU : Clock Generator= 64 EA, DVFS = support, PLL.1
[    0.000000] PLL : [0] =  550000000, [1] = 1200000000, [2] =  800000000, [3] =  614399000
[    0.000000] PLL1: CPU FCLK = 1200000000, HCLK = 300000000
[    0.000000] PLL2: BUS BCLK =  400000000, PCLK = 200000000
[    0.000000] PLL2: MEM MCLK =  800000000, DCLK = 800000000, BCLK = 400000000, PCLK = 200000000
[    0.000000] PLL0: G3D BCLK =  550000000
[    0.000000] PLL2: MPG BCLK =  400000000, PCLK = 200000000
[    0.000000] PERCPU: Embedded 8 pages/cpu @81339000 s12288 r8192 d12288 u32768
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 259840
[    0.000000] Kernel command line: console=ttyAMA0,115200n8 root=/dev/mmcblk0p2 rootfstype=ext4 init=/sbin/init lcd=HDMI720P60
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] allocated 2097152 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.000000] Memory: 1024MB = 1024MB total
[    0.000000] Memory: 829296k/829296k available, 219280k reserved, 0K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xc0800000 - 0xfee00000   ( 998 MB)
[    0.000000]     lowmem  : 0x80000000 - 0xc0000000   (1024 MB)
[    0.000000]     pkmap   : 0x7fe00000 - 0x80000000   (   2 MB)
[    0.000000]     modules : 0x7f000000 - 0x7fe00000   (  14 MB)
[    0.000000]       .text : 0x80008000 - 0x808a9244   (8837 kB)
[    0.000000]       .init : 0x808aa000 - 0x808e1000   ( 220 kB)
[    0.000000]       .data : 0x808e2000 - 0x80953d78   ( 456 kB)
[    0.000000]        .bss : 0x80953d9c - 0x80a31840   ( 887 kB)
[    0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] NR_IRQS:288
[    0.000000] VIC @f0002000: id 0x00041192, vendor 0x41
[    0.000000] VIC @f0003000: id 0x00041192, vendor 0x41
[    0.000000] GPIO  @f001a000: start  64, mask 0xffffffff (gpio 53)
[    0.000000] GPIO  @f001b000: start  96, mask 0xffffffff (gpio 54)
[    0.000000] GPIO  @f001c000: start 128, mask 0xffffffff (gpio 55)
[    0.000000] GPIO  @f001d000: start 160, mask 0xffffffff (gpio 56)
[    0.000000] GPIO  @f001e000: start 192, mask 0xffffffff (gpio 57)
[    0.000000] ALIVE @f0010800: start 224, mask 0x000000ff (alive 4)
[    0.000000] GIC   @f0301000: start 256 (vic 31)
[    0.000000] timer.0: source,  10000000(HZ:250), mult:3355443200
[    0.000000] timer.1: event ,  10000000(HZ:250), mult:42949673
[    0.000000] sched_clock: 32 bits at 250 Hz, resolution 4000000ns, wraps every 4294967292ms
[    0.000000] Console: colour dummy device 80x30
[    0.000000] Calibrating delay loop... 2390.01 BogoMIPS (lpj=4780032)
[    0.036000] pid_max: default: 32768 minimum: 301
[    0.036000] Security Framework initialized
[    0.036000] SELinux:  Initializing.
[    0.036000] Mount-cache hash table entries: 512
[    0.036000] Initializing cgroup subsys debug
[    0.036000] Initializing cgroup subsys cpuacct
[    0.036000] Initializing cgroup subsys memory
[    0.036000] Initializing cgroup subsys freezer
[    0.036000] CPU: Testing write buffer coherency: ok
[    0.036000] CPU0: thread -1, cpu 0, socket 10, mpidr 80000a00
[    0.036000] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[    0.036000] Setting up static identity map for 0x4065e408 - 0x4065e460
[    0.036000] L310 cache controller enabled
[    0.036000] l2x0: 16 ways, CACHE_ID 0x4100c4c8, AUX_CTRL 0x70470001, Cache size: 1048576 B
[    0.076000] CPU1: thread -1, cpu 1, socket 10, mpidr 80000a01
[    0.108000] CPU2: thread -1, cpu 2, socket 10, mpidr 80000a02
[    0.140000] CPU3: thread -1, cpu 3, socket 10, mpidr 80000a03
[    0.140000] Brought up 4 CPUs
[    0.140000] SMP: Total of 4 processors activated (9560.06 BogoMIPS).
[    0.140000] devtmpfs: initialized
[    0.144000] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    0.144000] pwm: max = 50000000 hz
[    0.144000] prepare_gpio_suspend:
[    0.144000]   alfn[0][0]: 0x00000000, alfn[0][1]: 0x00000000
[    0.144000]   alfn[1][0]: 0x66800000, alfn[1][1]: 0x55555566
[    0.144000]   alfn[2][0]: 0x55555555, alfn[2][1]: 0x00555555
[    0.144000]   alfn[3][0]: 0x00000000, alfn[3][1]: 0x00000000
[    0.144000]   alfn[4][0]: 0x00000000, alfn[4][1]: 0x55540000
[    0.144000] dummy: 
[    0.144000] NET: Registered protocol family 16
[    0.144000] [Register machine platform devices]
[    0.144000] mach: add amba device uart-pl011.0 
[    0.144000] mach: add amba device uart-pl011.1 
[    0.144000] mach: add amba device pl08xdmac.0 
[    0.144000] mach: add amba device pl08xdmac.1 
[    0.144000] mach: add amba device ssp-pl022.0 
[    0.144000] mach: add device syncgen [2]
[    0.148000] mach: add device hdmi 
[    0.148000] mach: add device i2c bus (array:3) 
[    0.148000] mach: add device Real Time Clock  
[    0.148000] mach: add device generic pwm (array:1)
[    0.148000] mach: add device generic gpio (array:6)
[    0.148000] mach: add device i2s (array:1) 
[    0.148000] mach: add device spdif tx
[    0.148000] mach: add device usb_ehci
[    0.148000] mach: add device usb_ohci
[    0.148000] mach: add device usb otg
[    0.148000] mach: add device ion-nxp
[    0.148000] mach: add device adc
[    0.148000] mach: add graphic device opengl|es
[    0.148000] [Register board platform devices]
[    0.148000] plat: board revision 0
[    0.148000] plat: add dynamic frequency (pll.1)
[    0.148000] plat: add framebuffer
[    0.148000] plat: add device sdmmc [0]
[    0.148000] plat: add device sdmmc [1]
[    0.148000] plat: add device sdmmc [2]
[    0.148000] plat: add backlight pwm device
[    0.148000] plat: add device keypad
[    0.148000] plat: add device fixed voltage
[    0.152000] plat: add device spdif playback
[    0.152000] plat: add device nxp-v4l2
[    0.152000] plat: register spidev
[    0.152000] plat: add touch(ft5x0x) device
[    0.152000] plat: add device gpio_led
[    0.152000] 
[    0.152000] hw-breakpoint: Debug register access (0xee113e95) caused undefined instruction on CPU 1
[    0.152000] hw-breakpoint: Debug register access (0xee113e95) caused undefined instruction on CPU 2
[    0.152000] hw-breakpoint: Debug register access (0xee113e95) caused undefined instruction on CPU 3
[    0.152000] hw-breakpoint: CPU 2 debug is powered down!
[    0.152000] hw-breakpoint: CPU 3 debug is powered down!
[    0.152000] hw-breakpoint: CPU 1 debug is powered down!
[    0.152000] hw-breakpoint: Debug register access (0xee113e95) caused undefined instruction on CPU 0
[    0.152000] hw-breakpoint: CPU 0 debug is powered down!
[    0.152000] Serial: AMBA PL011 UART driver
[    0.152000] uart-pl011.0: ttyAMA0 at MMIO 0xc00a1000 (irq = 7) is a PL011 rev3
[    0.156000] console [ttyAMA0] enabled
[    0.160000] uart-pl011.1: ttyAMA1 at MMIO 0xc00a0000 (irq = 6) is a PL011 rev3
[    0.176000] bio: create slab <bio-0> at 0
[    0.180000] gpiochip_add: registered GPIOs 0 to 31 on device: nxp-gpio.0
[    0.184000] gpiochip_add: registered GPIOs 32 to 63 on device: nxp-gpio.1
[    0.188000] gpiochip_add: registered GPIOs 64 to 95 on device: nxp-gpio.2
[    0.192000] gpiochip_add: registered GPIOs 96 to 127 on device: nxp-gpio.3
[    0.196000] gpiochip_add: registered GPIOs 128 to 159 on device: nxp-gpio.4
[    0.200000] gpiochip_add: registered GPIOs 160 to 167 on device: nxp-gpio.5
[    0.204000] pl08xdmac pl08xdmac.0: Unbalanced pm_runtime_enable!
[    0.208000] pl08xdmac pl08xdmac.0: initialized 8 virtual memcpy channels
[    0.212000] pl08xdmac pl08xdmac.0: initialized 16 virtual slave channels
[    0.216000] pl08xdmac pl08xdmac.0: DMA: PL080 rev1 at 0xc0000000 irq 1
[    0.220000] pl08xdmac pl08xdmac.1: Unbalanced pm_runtime_enable!
[    0.224000] pl08xdmac pl08xdmac.1: initialized 8 virtual memcpy channels
[    0.228000] pl08xdmac pl08xdmac.1: initialized 15 virtual slave channels
[    0.236000] pl08xdmac pl08xdmac.1: DMA: PL080 rev1 at 0xc0001000 irq 2
[    0.240000] fixed_vdds: 1350 mV 
[    0.244000] nxp_ion_probe success!!!
[    0.248000] SCSI subsystem initialized
[    0.252000] ssp-pl022 ssp-pl022.0: ARM PL022 driver, device ID: 0x00041022
[    0.256000] pl022: mapped registers from 0xc005b000 to f005b000
[    0.260000] ssp-pl022 ssp-pl022.0: setup for DMA on RX dma1chan7, TX dma1chan6
[    0.264000] ssp-pl022 ssp-pl022.0: will use autosuspend for runtime pm, delay 10ms
[    0.268000] usbcore: registered new interface driver usbfs
[    0.272000] usbcore: registered new interface driver hub
[    0.276000] usbcore: registered new device driver usb
[    0.280000] nxp-i2c.0:   390625 hz [pclk=200000000, clk = 256, scale= 1, timeout= 500 ms]
[    0.288000] nxp-i2c.1:    97656 hz [pclk=200000000, clk = 256, scale= 7, timeout= 500 ms]
[    0.292000] nxp-i2c.2:   195312 hz [pclk=200000000, clk = 256, scale= 3, timeout= 500 ms]
[    0.296000] Linux media interface: v0.10
[    0.300000] Linux video capture interface: v2.00
[    0.304000] pps_core: LinuxPPS API ver. 1 registered
[    0.308000] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.312000] PTP clock support registered
[    0.316000] Advanced Linux Sound Architecture Driver Version 1.0.25.
[    0.320000] Bluetooth: Core ver 2.16
[    0.324000] NET: Registered protocol family 31
[    0.328000] Bluetooth: HCI device and connection manager initialized
[    0.332000] Bluetooth: HCI socket layer initialized
[    0.336000] Bluetooth: L2CAP socket layer initialized
[    0.340000] Bluetooth: SCO socket layer initialized
[    0.344000] cfg80211: Calling CRDA to update world regulatory domain
[    0.344000] Switching to clocksource source timer
[    0.364000] NET: Registered protocol family 2
[    0.368000] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.376000] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.384000] TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
[    0.392000] TCP: Hash tables configured (established 131072 bind 65536)
[    0.400000] TCP: reno registered
[    0.404000] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.408000] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.416000] NET: Registered protocol family 1
[    0.420000] RPC: Registered named UNIX socket transport module.
[    0.424000] RPC: Registered udp transport module.
[    0.432000] RPC: Registered tcp transport module.
[    0.436000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.440000] Disply Reset Status : On
[    0.472000] find cec header!_edid_find_target_cec_address: cec physical address 1000
[    0.480000] hdmi_get_edid_preset: preferred_preset is supported
[    0.484000] Display HDMI register operation 
[    0.488000] Display.0 fps=161 (6 ms), wait= 4 jiffies, Pixelclk=200000000hz
[    0.496000] bt_bcm: rfkill initialized
[    0.500000] audit: initializing netlink socket (disabled)
[    0.508000] type=2000 audit(0.508:1): initialized
[    0.516000] NFS: Registering the id_resolver key type
[    0.524000] fuse init (API version 7.18)
[    0.528000] msgmni has been set to 1619
[    0.532000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[    0.540000] io scheduler noop registered
[    0.544000] io scheduler deadline registered
[    0.548000] io scheduler cfq registered (default)
[    0.552000] display.0 connected to fb.0  ...
[    0.556000] nxp-fb.0: dma addr = 0x74000000, buf[0xb30c8400]
[    0.560000] nxp-fb.0: dma addr = 0x74384000, buf[0xb30c85c0]
[    0.624000] hdmi_stop entered
[    0.628000] hdmi_run entered
[    0.640000] HDMI PHY Ready!!!
[    0.644000] Display.0 fps=161 (6 ms), wait= 4 jiffies, Pixelclk=200000000hz
[    0.648000] _calc_hdmi_sync_param: _h_sync_offset 0
[    0.680000] hdmi_run exit
[    0.680000] nxp-fb 0: out[0], 1280 * 720 - 32 bpp (phys:74000000 virt:0xb4000000 max:7372800)
[    0.696000] uart-pl011 uart-pl011.0: no DMA platform data
[    0.700000] uart-pl011 uart-pl011.1: no DMA platform data
[    0.708000] loop: module loaded
[    0.712000] tun: Universal TUN/TAP device driver, 1.6
[    0.716000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    0.724000] PPP generic driver version 2.4.2
[    0.728000] PPP BSD Compression module registered
[    0.732000] PPP Deflate Compression module registered
[    0.736000] PPP MPPE Compression module registered
[    0.740000] NET: Registered protocol family 24
[    0.748000] usbcore: registered new interface driver asix
[    0.752000] usbcore: registered new interface driver cdc_ether
[    0.756000] usbcore: registered new interface driver net1080
[    0.764000] usbcore: registered new interface driver cdc_subset
[    0.768000] usbcore: registered new interface driver zaurus
[    0.776000] usbcore: registered new interface driver cdc_ncm
[    0.780000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.788000] nxp-ehci nxp-ehci: SLsi Synopsys EHCI Host Controller
[    0.792000] nxp-ehci nxp-ehci: new USB bus registered, assigned bus number 1
[    0.800000] nxp-ehci nxp-ehci: irq 50, io mem 0xc0030000
[    0.816000] nxp-ehci nxp-ehci: USB 0.0 started, EHCI 1.00
[    0.820000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    0.828000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.832000] usb usb1: Product: SLsi Synopsys EHCI Host Controller
[    0.840000] usb usb1: Manufacturer: Linux 3.4.39-FriendlyARM ehci_hcd
[    0.848000] usb usb1: SerialNumber: nxp-ehci
[    0.852000] hub 1-0:1.0: USB hub found
[    0.856000] hub 1-0:1.0: 3 ports detected
[    0.860000] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[    1.064000] Core Release: 2.93a
[    1.068000] Setting default values for core params
[    1.072000] Finished setting default values for core params
[    1.276000] Using Descriptor DMA mode
[    1.280000] Dedicated Tx FIFOs mode
[    1.284000] dwc_otg dwc_otg: DWC OTG Controller
[    1.288000] dwc_otg dwc_otg: new USB bus registered, assigned bus number 2
[    1.296000] dwc_otg dwc_otg: irq 49, io mem 0x00000000
[    1.300000] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    1.308000] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.316000] usb usb2: Product: DWC OTG Controller
[    1.320000] usb usb2: Manufacturer: Linux 3.4.39-FriendlyARM dwc_otg_hcd
[    1.328000] usb usb2: SerialNumber: dwc_otg
[    1.332000] hub 2-0:1.0: USB hub found
[    1.336000] hub 2-0:1.0: 1 port detected
[    1.340000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.344000] nxp-ohci nxp-ohci: SLsi Synopsys OHCI Host Controller
[    1.352000] nxp-ohci nxp-ohci: new USB bus registered, assigned bus number 3
[    1.360000] nxp-ohci nxp-ohci: irq 50, io mem 0xc0020000
[    1.424000] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[    1.428000] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.436000] usb usb3: Product: SLsi Synopsys OHCI Host Controller
[    1.444000] HDMI HPD State 0x1
[    1.444000] usb usb3: Manufacturer: Linux 3.4.39-FriendlyARM ohci_hcd
[    1.452000] usb usb3: SerialNumber: nxp-ohci
[    1.456000] hub 3-0:1.0: USB hub found
[    1.460000] hub 3-0:1.0: 3 ports detected
[    1.464000] Initializing USB Mass Storage driver...
[    1.468000] usbcore: registered new interface driver usb-storage
[    1.476000] USB Mass Storage support registered.
[    1.480000] android_usb gadget: Mass Storage Function, version: 2009/09/11
[    1.488000] android_usb gadget: Number of LUNs=1
[    1.492000]  lun0: LUN: removable file: (no medium)
[    1.496000] find cec header!_edid_find_target_cec_address: cec physical address 1000
[    1.500000] android_usb gadget: android_usb ready
[    1.500000] mousedev: PS/2 mouse device common for all mice
[    1.500000] input: Nexell Keypad as /devices/platform/nxp-keypad/input/input0
[    1.500000] usbcore: registered new interface driver xpad
[    1.500000] input: ft5x0x_ts as /devices/virtual/input/input1
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:1)
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:2)
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:3)
[    1.508000] Error: i2c.2, addr:70, trans len:-11(1), try:3
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:1)
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:2)
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:3)
[    1.508000] Error: i2c.2, addr:70, trans len:-11(1), try:3
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:1)
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:2)
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:3)
[    1.508000] Error: i2c.2, addr:70, trans len:-11(1), try:3
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:1)
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:2)
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:3)
[    1.508000] Error: i2c.2, addr:70, trans len:-11(1), try:3
[    1.508000] read reg (0xa6) error, -11
[    1.508000] ft5x0x_ts 2-0038: chip not found
[    1.680000] _hdmi_hpd_changed: edid update success, preset 18
[    1.684000] notify_hpd_changed: state 1
[    1.688000] hdmi_run entered
[    1.692000] hdmi_run: hdmi already running!
[    1.736000] ft5x0x_ts 2-0038: probe ft5x0x TouchScreen failed, -11
[    1.740000] ft5x0x_ts: probe of 2-0038 failed with error -11
[    1.748000] [RTC] day=2009.09.01 time=00:00:00
[    1.752000] nxp-rtc nxp-rtc.0: rtc core: registered nxp-rtc as rtc0
[    1.756000] i2c /dev entries driver
[    1.760000] gspca_main: v2.14.0 registered
[    1.768000] usbcore: registered new interface driver uvcvideo
[    1.772000] USB Video Class driver (1.1.1)
[    1.776000] device-mapper: uevent: version 1.0.3
[    1.784000] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
[    1.792000] Bluetooth: HCI UART driver ver 2.2
[    1.796000] Bluetooth: HCI H4 protocol initialized
[    1.800000] DVFS: ASV[0] IDS(10mA, 10) Ro(110, 95)
[    1.804000] ASV  0 =  1400000khz,  1350000 uV 
[    1.808000] ASV  1 =  1200000khz,  1250000 uV 
[    1.812000] ASV  2 =  1000000khz,  1175000 uV 
[    1.820000] ASV  3 =   800000khz,  1125000 uV 
[    1.824000] ASV  4 =   700000khz,  1100000 uV 
[    1.828000] ASV  5 =   600000khz,  1075000 uV 
[    1.832000] ASV  6 =   500000khz,  1075000 uV 
[    1.836000] ASV  7 =   400000khz,  1075000 uV 
[    1.840000] DVFS: regulator vdd_arm_1.3V
[    1.844000] DVFS: cpu DVFS with PLL.1 [tables=8]
[    1.852000] cpuidle: using governor ladder
[    1.856000] cpuidle: using governor menu
[    1.860000] Synopsys Designware Multimedia Card Interface Driver
[    1.864000] dw_mmc dw_mmc.0: Using internal DMA controller.
[    1.872000] ------------[ cut here ]------------
[    1.872000] mmc0: no vmmc regulator found
[    1.872000] dw_mmc dw_mmc.0: Using external card detect irq 225 (io 161)
[    1.872000] dw_mmc dw_mmc.0: Version ID is 250a
[    1.872000] dw_mmc dw_mmc.0: DW MMC controller at irq 43, 32 bit host data width, 32 deep fifo hw timeout 500 ms
[    1.872000] dw_mmc dw_mmc.1: Using PIO mode.
[    1.872000] mmc1: no vmmc regulator found
[    1.872000] dw_mmc dw_mmc.1: Version ID is 250a
[    1.872000] dw_mmc dw_mmc.1: DW MMC controller at irq 44, 32 bit host data width, 32 deep fifo hw timeout 500 ms
[    1.872000] dw_mmc dw_mmc.2: Using internal DMA controller.
[    1.872000] mmc2: no vmmc regulator found
[    1.872000] dw_mmc dw_mmc.2: Using external card detect irq 152 (io 88)
[    1.940000] WARNING: at kernel/sched/core.c:3222 _raw_spin_unlock+0x20/0x40()
[    1.948000] Modules linked in:
[    1.952000] [<800154ac>] (unwind_backtrace+0x0/0x12c) from [<800441a8>] (warn_slowpath_common+0x54/0x64)
[    1.960000] [<800441a8>] (warn_slowpath_common+0x54/0x64) from [<80044254>] (warn_slowpath_null+0x1c/0x24)
[    1.968000] [<80044254>] (warn_slowpath_null+0x1c/0x24) from [<8065db28>] (_raw_spin_unlock+0x20/0x40)
[    1.980000] [<8065db28>] (_raw_spin_unlock+0x20/0x40) from [<8045b214>] (cpufreq_stats_update+0x78/0x80)
[    1.988000] [<8045b214>] (cpufreq_stats_update+0x78/0x80) from [<8045b600>] (cpufreq_stat_notifier_trans+0x94/0xc8)
[    2.000000] [<8045b600>] (cpufreq_stat_notifier_trans+0x94/0xc8) from [<800693a8>] (notifier_call_chain+0x44/0x84)
[    2.008000] [<800693a8>] (notifier_call_chain+0x44/0x84) from [<80069780>] (__srcu_notifier_call_chain+0x44/0x60)
[    2.020000] [<80069780>] (__srcu_notifier_call_chain+0x44/0x60) from [<800697b4>] (srcu_notifier_call_chain+0x18/0x20)
[    2.032000] [<800697b4>] (srcu_notifier_call_chain+0x18/0x20) from [<80458bdc>] (cpufreq_notify_transition+0xb8/0x28c)
[    2.040000] [<80458bdc>] (cpufreq_notify_transition+0xb8/0x28c) from [<80461568>] (nxp_cpufreq_change_frequency+0xd8/0x1cc)
[    2.052000] [<80461568>] (nxp_cpufreq_change_frequency+0xd8/0x1cc) from [<80461794>] (nxp_cpufreq_target+0x138/0x388)
[    2.064000] [<80461794>] (nxp_cpufreq_target+0x138/0x388) from [<8045fe04>] (cpufreq_interactive_speedchange_task+0x178/0x220)

--------------------------------------------------------------------------------
 Second Boot by Nexell Co. : Built on Nov 19 2014 20:10:38
--------------------------------------------------------------------------------
 PLL0: 550000000   PLL1: 1200000000   PLL2: 800000000   PLL3: 612000000

 Divider0 PLL: 1 CPU:1200000000   CPU BUS:300000000
 Divider1 PLL: 2 BCLK:400000000   PCLK:200000000
 Divider2 PLL: 2 MDCLK:800000000   MCLK:800000000   
		 MBCLK:400000000   MPCLK:200000000
 Divider3 PLL: 0 G3D BCLK:550000000
 Divider4 PLL: 2 MPEG BCLK:400000000   MPEG PCLK:200000000

123
DDR3 POR Init Start
phy init

########## READ/GATE Level ##########
DDR3 Init Done!
Loading from sdmmc...
 Image Loading Done!
Launch to 0x42C00000


U-Boot 2014.07-gd46d757 (Nov 27 2015 - 17:09:12)

PLL : [0] =  550000000, [1] = 1200000000, [2] =  800000000, [3] =  614399000
PLL1: CPU FCLK = 1200000000, HCLK = 300000000
PLL2: BUS BCLK =  400000000, PCLK = 200000000
PLL2: MEM MCLK =  800000000, DCLK = 800000000, BCLK = 400000000, PCLK = 200000000
PLL0: G3D BCLK =  550000000
PLL2: MPG BCLK =  400000000, PCLK = 200000000
I2C:   ready
DRAM:  256 MiB
Heap = 0x43000000~0x45000000
Code = 0x42c00000~0x42c72984
GLD  = 0x42bffeb8
GLBD = 0x42bffe68
SP   = 0x42bffe68,0x42bffe50(CURR)
PC   = 0x42c06114
TAGS = 0x40000100 
PAGE = 0x42c80000~0x42c8c000
MACH = [4330]   
VER  = 1      
BOARD= [nanopi2]    
LCD  = N/A (-1)
MMC:   NXP DWMMC: 0, NXP DWMMC: 1, NXP DWMMC: 2
In:    serial
Out:   serial
Err:   serial
switch to partitions #0, OK
mmc0 is current device
Writing to MMC(0)... done
HDMI: display.0, preset 0 (1280 *  720)
HDMI: PHY Ready!!!
DONE: Logo bmp 800 by 480 (3bpp), len=1152056 

DRAW: 0x47000000 -> 0x46000000 

Hit any key to stop autoboot:  1  0 
## Booting kernel from Legacy Image at 48000000 ...
   Image Name:   Linux-3.4.39-FriendlyARM
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4767712 Bytes = 4.5 MiB
   Load Address: 40008000
   Entry Point:  40008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 3.4.39-FriendlyARM (root@jensen) (gcc version 4.9.3 (ctng-1.21.0-229g-FA) ) #1 SMP PREEMPT Sat Nov 28 17:36:10 HKT 2015
[    0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine: NANOPI2
[    0.000000] Display: HDMI selected
[    0.000000] nxp_reserve_mem: reserve CMA: size 201326592
[    0.000000] NXP/CMA: Reserved 0x74000000/0x0c000000 for 'ion'
[    0.000000] NXP/CMA: success register cma region for 'ion'
[    0.000000] Memory policy: ECC disabled, Data cache writealloc
[    0.000000] CPU : iomap[ 0]: p 0xc0000000 -> v 0xf0000000 len=0x300000
[    0.000000] CPU : iomap[ 1]: p 0xf0000000 -> v 0xf0300000 len=0x100000
[    0.000000] CPU : iomap[ 2]: p 0xcf000000 -> v 0xf0400000 len=0x100000
[    0.000000] CPU : iomap[ 3]: p 0x2c000000 -> v 0xf0500000 len=0x100000
[    0.000000] CPU : iomap[ 4]: p 0x00000000 -> v 0xf0600000 len=0x100000
[    0.000000] CPU : DMA Zone Size =16M, CORE 4
[    0.000000] CPU : VERSION = 2 (0xE153000A), Assign Peripheral Exclusive Bus
[    0.000000] s5p4418-NanoPi2: Board initialized
[    0.000000] CPU : Clock Generator= 64 EA, DVFS = support, PLL.1
[    0.000000] PLL : [0] =  550000000, [1] = 1200000000, [2] =  800000000, [3] =  614399000
[    0.000000] PLL1: CPU FCLK = 1200000000, HCLK = 300000000
[    0.000000] PLL2: BUS BCLK =  400000000, PCLK = 200000000
[    0.000000] PLL2: MEM MCLK =  800000000, DCLK = 800000000, BCLK = 400000000, PCLK = 200000000
[    0.000000] PLL0: G3D BCLK =  550000000
[    0.000000] PLL2: MPG BCLK =  400000000, PCLK = 200000000
[    0.000000] PERCPU: Embedded 8 pages/cpu @81339000 s12288 r8192 d12288 u32768
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 259840
[    0.000000] Kernel command line: console=ttyAMA0,115200n8 root=/dev/mmcblk0p2 rootfstype=ext4 init=/sbin/init lcd=HDMI720P60
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] allocated 2097152 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.000000] Memory: 1024MB = 1024MB total
[    0.000000] Memory: 829296k/829296k available, 219280k reserved, 0K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xc0800000 - 0xfee00000   ( 998 MB)
[    0.000000]     lowmem  : 0x80000000 - 0xc0000000   (1024 MB)
[    0.000000]     pkmap   : 0x7fe00000 - 0x80000000   (   2 MB)
[    0.000000]     modules : 0x7f000000 - 0x7fe00000   (  14 MB)
[    0.000000]       .text : 0x80008000 - 0x808a9244   (8837 kB)
[    0.000000]       .init : 0x808aa000 - 0x808e1000   ( 220 kB)
[    0.000000]       .data : 0x808e2000 - 0x80953d78   ( 456 kB)
[    0.000000]        .bss : 0x80953d9c - 0x80a31840   ( 887 kB)
[    0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] NR_IRQS:288
[    0.000000] VIC @f0002000: id 0x00041192, vendor 0x41
[    0.000000] VIC @f0003000: id 0x00041192, vendor 0x41
[    0.000000] GPIO  @f001a000: start  64, mask 0xffffffff (gpio 53)
[    0.000000] GPIO  @f001b000: start  96, mask 0xffffffff (gpio 54)
[    0.000000] GPIO  @f001c000: start 128, mask 0xffffffff (gpio 55)
[    0.000000] GPIO  @f001d000: start 160, mask 0xffffffff (gpio 56)
[    0.000000] GPIO  @f001e000: start 192, mask 0xffffffff (gpio 57)
[    0.000000] ALIVE @f0010800: start 224, mask 0x000000ff (alive 4)
[    0.000000] GIC   @f0301000: start 256 (vic 31)
[    0.000000] timer.0: source,  10000000(HZ:250), mult:3355443200
[    0.000000] timer.1: event ,  10000000(HZ:250), mult:42949673
[    0.000000] sched_clock: 32 bits at 250 Hz, resolution 4000000ns, wraps every 4294967292ms
[    0.000000] Console: colour dummy device 80x30
[    0.000000] Calibrating delay loop... 2390.01 BogoMIPS (lpj=4780032)
[    0.036000] pid_max: default: 32768 minimum: 301
[    0.036000] Security Framework initialized
[    0.036000] SELinux:  Initializing.
[    0.036000] Mount-cache hash table entries: 512
[    0.036000] Initializing cgroup subsys debug
[    0.036000] Initializing cgroup subsys cpuacct
[    0.036000] Initializing cgroup subsys memory
[    0.036000] Initializing cgroup subsys freezer
[    0.036000] CPU: Testing write buffer coherency: ok
[    0.036000] CPU0: thread -1, cpu 0, socket 10, mpidr 80000a00
[    0.036000] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[    0.036000] Setting up static identity map for 0x4065e408 - 0x4065e460
[    0.036000] L310 cache controller enabled
[    0.036000] l2x0: 16 ways, CACHE_ID 0x4100c4c8, AUX_CTRL 0x70470001, Cache size: 1048576 B
[    0.076000] CPU1: thread -1, cpu 1, socket 10, mpidr 80000a01
[    0.108000] CPU2: thread -1, cpu 2, socket 10, mpidr 80000a02
[    0.140000] CPU3: thread -1, cpu 3, socket 10, mpidr 80000a03
[    0.140000] Brought up 4 CPUs
[    0.140000] SMP: Total of 4 processors activated (9560.06 BogoMIPS).
[    0.140000] devtmpfs: initialized
[    0.144000] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    0.144000] pwm: max = 50000000 hz
[    0.144000] prepare_gpio_suspend:
[    0.144000]   alfn[0][0]: 0x00000000, alfn[0][1]: 0x00000000
[    0.144000]   alfn[1][0]: 0x66800000, alfn[1][1]: 0x55555566
[    0.144000]   alfn[2][0]: 0x55555555, alfn[2][1]: 0x00555555
[    0.144000]   alfn[3][0]: 0x00000000, alfn[3][1]: 0x00000000
[    0.144000]   alfn[4][0]: 0x00000000, alfn[4][1]: 0x55540000
[    0.144000] dummy: 
[    0.144000] NET: Registered protocol family 16
[    0.144000] [Register machine platform devices]
[    0.144000] mach: add amba device uart-pl011.0 
[    0.144000] mach: add amba device uart-pl011.1 
[    0.144000] mach: add amba device pl08xdmac.0 
[    0.144000] mach: add amba device pl08xdmac.1 
[    0.144000] mach: add amba device ssp-pl022.0 
[    0.144000] mach: add device syncgen [2]
[    0.148000] mach: add device hdmi 
[    0.148000] mach: add device i2c bus (array:3) 
[    0.148000] mach: add device Real Time Clock  
[    0.148000] mach: add device generic pwm (array:1)
[    0.148000] mach: add device generic gpio (array:6)
[    0.148000] mach: add device i2s (array:1) 
[    0.148000] mach: add device spdif tx
[    0.148000] mach: add device usb_ehci
[    0.148000] mach: add device usb_ohci
[    0.148000] mach: add device usb otg
[    0.148000] mach: add device ion-nxp
[    0.148000] mach: add device adc
[    0.148000] mach: add graphic device opengl|es
[    0.148000] [Register board platform devices]
[    0.148000] plat: board revision 0
[    0.148000] plat: add dynamic frequency (pll.1)
[    0.148000] plat: add framebuffer
[    0.148000] plat: add device sdmmc [0]
[    0.148000] plat: add device sdmmc [1]
[    0.148000] plat: add device sdmmc [2]
[    0.148000] plat: add backlight pwm device
[    0.148000] plat: add device keypad
[    0.148000] plat: add device fixed voltage
[    0.152000] plat: add device spdif playback
[    0.152000] plat: add device nxp-v4l2
[    0.152000] plat: register spidev
[    0.152000] plat: add touch(ft5x0x) device
[    0.152000] plat: add device gpio_led
[    0.152000] 
[    0.152000] hw-breakpoint: Debug register access (0xee113e95) caused undefined instruction on CPU 1
[    0.152000] hw-breakpoint: Debug register access (0xee113e95) caused undefined instruction on CPU 2
[    0.152000] hw-breakpoint: Debug register access (0xee113e95) caused undefined instruction on CPU 3
[    0.152000] hw-breakpoint: CPU 2 debug is powered down!
[    0.152000] hw-breakpoint: CPU 3 debug is powered down!
[    0.152000] hw-breakpoint: CPU 1 debug is powered down!
[    0.152000] hw-breakpoint: Debug register access (0xee113e95) caused undefined instruction on CPU 0
[    0.152000] hw-breakpoint: CPU 0 debug is powered down!
[    0.152000] Serial: AMBA PL011 UART driver
[    0.152000] uart-pl011.0: ttyAMA0 at MMIO 0xc00a1000 (irq = 7) is a PL011 rev3
[    0.156000] console [ttyAMA0] enabled
[    0.160000] uart-pl011.1: ttyAMA1 at MMIO 0xc00a0000 (irq = 6) is a PL011 rev3
[    0.176000] bio: create slab <bio-0> at 0
[    0.180000] gpiochip_add: registered GPIOs 0 to 31 on device: nxp-gpio.0
[    0.184000] gpiochip_add: registered GPIOs 32 to 63 on device: nxp-gpio.1
[    0.188000] gpiochip_add: registered GPIOs 64 to 95 on device: nxp-gpio.2
[    0.192000] gpiochip_add: registered GPIOs 96 to 127 on device: nxp-gpio.3
[    0.196000] gpiochip_add: registered GPIOs 128 to 159 on device: nxp-gpio.4
[    0.200000] gpiochip_add: registered GPIOs 160 to 167 on device: nxp-gpio.5
[    0.204000] pl08xdmac pl08xdmac.0: Unbalanced pm_runtime_enable!
[    0.208000] pl08xdmac pl08xdmac.0: initialized 8 virtual memcpy channels
[    0.212000] pl08xdmac pl08xdmac.0: initialized 16 virtual slave channels
[    0.216000] pl08xdmac pl08xdmac.0: DMA: PL080 rev1 at 0xc0000000 irq 1
[    0.220000] pl08xdmac pl08xdmac.1: Unbalanced pm_runtime_enable!
[    0.224000] pl08xdmac pl08xdmac.1: initialized 8 virtual memcpy channels
[    0.228000] pl08xdmac pl08xdmac.1: initialized 15 virtual slave channels
[    0.236000] pl08xdmac pl08xdmac.1: DMA: PL080 rev1 at 0xc0001000 irq 2
[    0.240000] fixed_vdds: 1350 mV 
[    0.244000] nxp_ion_probe success!!!
[    0.248000] SCSI subsystem initialized
[    0.252000] ssp-pl022 ssp-pl022.0: ARM PL022 driver, device ID: 0x00041022
[    0.256000] pl022: mapped registers from 0xc005b000 to f005b000
[    0.260000] ssp-pl022 ssp-pl022.0: setup for DMA on RX dma1chan7, TX dma1chan6
[    0.264000] ssp-pl022 ssp-pl022.0: will use autosuspend for runtime pm, delay 10ms
[    0.268000] usbcore: registered new interface driver usbfs
[    0.272000] usbcore: registered new interface driver hub
[    0.276000] usbcore: registered new device driver usb
[    0.280000] nxp-i2c.0:   390625 hz [pclk=200000000, clk = 256, scale= 1, timeout= 500 ms]
[    0.288000] nxp-i2c.1:    97656 hz [pclk=200000000, clk = 256, scale= 7, timeout= 500 ms]
[    0.292000] nxp-i2c.2:   195312 hz [pclk=200000000, clk = 256, scale= 3, timeout= 500 ms]
[    0.296000] Linux media interface: v0.10
[    0.300000] Linux video capture interface: v2.00
[    0.304000] pps_core: LinuxPPS API ver. 1 registered
[    0.308000] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.312000] PTP clock support registered
[    0.316000] Advanced Linux Sound Architecture Driver Version 1.0.25.
[    0.320000] Bluetooth: Core ver 2.16
[    0.324000] NET: Registered protocol family 31
[    0.328000] Bluetooth: HCI device and connection manager initialized
[    0.332000] Bluetooth: HCI socket layer initialized
[    0.336000] Bluetooth: L2CAP socket layer initialized
[    0.340000] Bluetooth: SCO socket layer initialized
[    0.344000] cfg80211: Calling CRDA to update world regulatory domain
[    0.344000] Switching to clocksource source timer
[    0.364000] NET: Registered protocol family 2
[    0.368000] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.376000] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.384000] TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
[    0.392000] TCP: Hash tables configured (established 131072 bind 65536)
[    0.400000] TCP: reno registered
[    0.404000] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.408000] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.416000] NET: Registered protocol family 1
[    0.420000] RPC: Registered named UNIX socket transport module.
[    0.424000] RPC: Registered udp transport module.
[    0.432000] RPC: Registered tcp transport module.
[    0.436000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.440000] Disply Reset Status : On
[    0.472000] find cec header!_edid_find_target_cec_address: cec physical address 1000
[    0.480000] hdmi_get_edid_preset: preferred_preset is supported
[    0.484000] Display HDMI register operation 
[    0.488000] Display.0 fps=161 (6 ms), wait= 4 jiffies, Pixelclk=200000000hz
[    0.496000] bt_bcm: rfkill initialized
[    0.500000] audit: initializing netlink socket (disabled)
[    0.508000] type=2000 audit(0.508:1): initialized
[    0.516000] NFS: Registering the id_resolver key type
[    0.524000] fuse init (API version 7.18)
[    0.528000] msgmni has been set to 1619
[    0.532000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[    0.540000] io scheduler noop registered
[    0.544000] io scheduler deadline registered
[    0.548000] io scheduler cfq registered (default)
[    0.552000] display.0 connected to fb.0  ...
[    0.556000] nxp-fb.0: dma addr = 0x74000000, buf[0xb30c8400]
[    0.560000] nxp-fb.0: dma addr = 0x74384000, buf[0xb30c85c0]
[    0.624000] hdmi_stop entered
[    0.628000] hdmi_run entered
[    0.640000] HDMI PHY Ready!!!
[    0.644000] Display.0 fps=161 (6 ms), wait= 4 jiffies, Pixelclk=200000000hz
[    0.648000] _calc_hdmi_sync_param: _h_sync_offset 0
[    0.680000] hdmi_run exit
[    0.680000] nxp-fb 0: out[0], 1280 * 720 - 32 bpp (phys:74000000 virt:0xb4000000 max:7372800)
[    0.696000] uart-pl011 uart-pl011.0: no DMA platform data
[    0.700000] uart-pl011 uart-pl011.1: no DMA platform data
[    0.708000] loop: module loaded
[    0.712000] tun: Universal TUN/TAP device driver, 1.6
[    0.716000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    0.724000] PPP generic driver version 2.4.2
[    0.728000] PPP BSD Compression module registered
[    0.732000] PPP Deflate Compression module registered
[    0.736000] PPP MPPE Compression module registered
[    0.740000] NET: Registered protocol family 24
[    0.748000] usbcore: registered new interface driver asix
[    0.752000] usbcore: registered new interface driver cdc_ether
[    0.756000] usbcore: registered new interface driver net1080
[    0.764000] usbcore: registered new interface driver cdc_subset
[    0.768000] usbcore: registered new interface driver zaurus
[    0.776000] usbcore: registered new interface driver cdc_ncm
[    0.780000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.788000] nxp-ehci nxp-ehci: SLsi Synopsys EHCI Host Controller
[    0.792000] nxp-ehci nxp-ehci: new USB bus registered, assigned bus number 1
[    0.800000] nxp-ehci nxp-ehci: irq 50, io mem 0xc0030000
[    0.816000] nxp-ehci nxp-ehci: USB 0.0 started, EHCI 1.00
[    0.820000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    0.828000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.832000] usb usb1: Product: SLsi Synopsys EHCI Host Controller
[    0.840000] usb usb1: Manufacturer: Linux 3.4.39-FriendlyARM ehci_hcd
[    0.848000] usb usb1: SerialNumber: nxp-ehci
[    0.852000] hub 1-0:1.0: USB hub found
[    0.856000] hub 1-0:1.0: 3 ports detected
[    0.860000] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[    1.064000] Core Release: 2.93a
[    1.068000] Setting default values for core params
[    1.072000] Finished setting default values for core params
[    1.276000] Using Descriptor DMA mode
[    1.280000] Dedicated Tx FIFOs mode
[    1.284000] dwc_otg dwc_otg: DWC OTG Controller
[    1.288000] dwc_otg dwc_otg: new USB bus registered, assigned bus number 2
[    1.296000] dwc_otg dwc_otg: irq 49, io mem 0x00000000
[    1.300000] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    1.308000] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.316000] usb usb2: Product: DWC OTG Controller
[    1.320000] usb usb2: Manufacturer: Linux 3.4.39-FriendlyARM dwc_otg_hcd
[    1.328000] usb usb2: SerialNumber: dwc_otg
[    1.332000] hub 2-0:1.0: USB hub found
[    1.336000] hub 2-0:1.0: 1 port detected
[    1.340000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.344000] nxp-ohci nxp-ohci: SLsi Synopsys OHCI Host Controller
[    1.352000] nxp-ohci nxp-ohci: new USB bus registered, assigned bus number 3
[    1.360000] nxp-ohci nxp-ohci: irq 50, io mem 0xc0020000
[    1.424000] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[    1.428000] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.436000] usb usb3: Product: SLsi Synopsys OHCI Host Controller
[    1.444000] HDMI HPD State 0x1
[    1.444000] usb usb3: Manufacturer: Linux 3.4.39-FriendlyARM ohci_hcd
[    1.452000] usb usb3: SerialNumber: nxp-ohci
[    1.456000] hub 3-0:1.0: USB hub found
[    1.460000] hub 3-0:1.0: 3 ports detected
[    1.464000] Initializing USB Mass Storage driver...
[    1.468000] usbcore: registered new interface driver usb-storage
[    1.476000] USB Mass Storage support registered.
[    1.480000] android_usb gadget: Mass Storage Function, version: 2009/09/11
[    1.488000] android_usb gadget: Number of LUNs=1
[    1.492000]  lun0: LUN: removable file: (no medium)
[    1.496000] find cec header!_edid_find_target_cec_address: cec physical address 1000
[    1.500000] android_usb gadget: android_usb ready
[    1.500000] mousedev: PS/2 mouse device common for all mice
[    1.500000] input: Nexell Keypad as /devices/platform/nxp-keypad/input/input0
[    1.500000] usbcore: registered new interface driver xpad
[    1.500000] input: ft5x0x_ts as /devices/virtual/input/input1
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:1)
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:2)
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:3)
[    1.508000] Error: i2c.2, addr:70, trans len:-11(1), try:3
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:1)
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:2)
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:3)
[    1.508000] Error: i2c.2, addr:70, trans len:-11(1), try:3
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:1)
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:2)
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:3)
[    1.508000] Error: i2c.2, addr:70, trans len:-11(1), try:3
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:1)
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:2)
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:3)
[    1.508000] Error: i2c.2, addr:70, trans len:-11(1), try:3
[    1.508000] read reg (0xa6) error, -11
[    1.508000] ft5x0x_ts 2-0038: chip not found
[    1.680000] _hdmi_hpd_changed: edid update success, preset 18
[    1.684000] notify_hpd_changed: state 1
[    1.688000] hdmi_run entered
[    1.692000] hdmi_run: hdmi already running!
[    1.724000] ft5x0x_ts 2-0038: probe ft5x0x TouchScreen failed, -11
[    1.728000] ft5x0x_ts: probe of 2-0038 failed with error -11
[    1.736000] [RTC] day=2009.09.01 time=00:00:00
[    1.740000] nxp-rtc nxp-rtc.0: rtc core: registered nxp-rtc as rtc0
[    1.744000] i2c /dev entries driver
[    1.748000] gspca_main: v2.14.0 registered
[    1.756000] usbcore: registered new interface driver uvcvideo
[    1.760000] USB Video Class driver (1.1.1)
[    1.764000] device-mapper: uevent: version 1.0.3
[    1.772000] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
[    1.780000] Bluetooth: HCI UART driver ver 2.2
[    1.784000] Bluetooth: HCI H4 protocol initialized
[    1.788000] DVFS: ASV[0] IDS(10mA, 10) Ro(110, 95)
[    1.792000] ASV  0 =  1400000khz,  1350000 uV 
[    1.796000] ASV  1 =  1200000khz,  1250000 uV 
[    1.800000] ASV  2 =  1000000khz,  1175000 uV 
[    1.808000] ASV  3 =   800000khz,  1125000 uV 
[    1.812000] ASV  4 =   700000khz,  1100000 uV 
[    1.816000] ASV  5 =   600000khz,  1075000 uV 
[    1.820000] ASV  6 =   500000khz,  1075000 uV 
[    1.824000] ASV  7 =   400000khz,  1075000 uV 
[    1.828000] DVFS: regulator vdd_arm_1.3V
[    1.832000] DVFS: cpu DVFS with PLL.1 [tables=8]
[    1.840000] cpuidle: using governor ladder
[    1.844000] cpuidle: using governor menu
[    1.848000] Synopsys Designware Multimedia Card Interface Driver
[    1.852000] dw_mmc dw_mmc.0: Using internal DMA controller.
[    1.860000] mmc0: no vmmc regulator found
[    1.864000] dw_mmc dw_mmc.0: Using external card detect irq 225 (io 161)
[    1.872000] dw_mmc dw_mmc.0: Version ID is 250a
[    1.876000] dw_mmc dw_mmc.0: DW MMC controller at irq 43, 32 bit host data width, 32 deep fifo hw timeout 500 ms
[    1.884000] dw_mmc dw_mmc.1: Using PIO mode.
[    1.888000] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)
[    1.944000] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
[    1.952000] mmc0: new high speed SDHC card at address 0007

--------------------------------------------------------------------------------
 Second Boot by Nexell Co. : Built on Nov 19 2014 20:10:38
--------------------------------------------------------------------------------
 PLL0: 550000000   PLL1: 1200000000   PLL2: 800000000   PLL3: 612000000

 Divider0 PLL: 1 CPU:1200000000   CPU BUS:300000000
 Divider1 PLL: 2 BCLK:400000000   PCLK:200000000
 Divider2 PLL: 2 MDCLK:800000000   MCLK:800000000   
		 MBCLK:400000000   MPCLK:200000000
 Divider3 PLL: 0 G3D BCLK:550000000
 Divider4 PLL: 2 MPEG BCLK:400000000   MPEG PCLK:200000000

123
DDR3 POR Init Start
phy init

########## READ/GATE Level ##########
DDR3 Init Done!
Loading from sdmmc...
 Image Loading Done!
Launch to 0x42C00000


U-Boot 2014.07-gd46d757 (Nov 27 2015 - 17:09:12)

PLL : [0] =  550000000, [1] = 1200000000, [2] =  800000000, [3] =  614399000
PLL1: CPU FCLK = 1200000000, HCLK = 300000000
PLL2: BUS BCLK =  400000000, PCLK = 200000000
PLL2: MEM MCLK =  800000000, DCLK = 800000000, BCLK = 400000000, PCLK = 200000000
PLL0: G3D BCLK =  550000000
PLL2: MPG BCLK =  400000000, PCLK = 200000000
I2C:   ready
DRAM:  256 MiB
Heap = 0x43000000~0x45000000
Code = 0x42c00000~0x42c72984
GLD  = 0x42bffeb8
GLBD = 0x42bffe68
SP   = 0x42bffe68,0x42bffe50(CURR)
PC   = 0x42c06114
TAGS = 0x40000100 
PAGE = 0x42c80000~0x42c8c000
MACH = [4330]   
VER  = 1      
BOARD= [nanopi2]    
LCD  = N/A (-1)
MMC:   NXP DWMMC: 0, NXP DWMMC: 1, NXP DWMMC: 2
In:    serial
Out:   serial
Err:   serial
switch to partitions #0, OK
mmc0 is current device
Writing to MMC(0)... done
HDMI: display.0, preset 0 (1280 *  720)
HDMI: PHY Ready!!!
DONE: Logo bmp 800 by 480 (3bpp), len=1152056 

DRAW: 0x47000000 -> 0x46000000 

Hit any key to stop autoboot:  1  0 
## Booting kernel from Legacy Image at 48000000 ...
   Image Name:   Linux-3.4.39-FriendlyARM
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4767712 Bytes = 4.5 MiB
   Load Address: 40008000
   Entry Point:  40008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 3.4.39-FriendlyARM (root@jensen) (gcc version 4.9.3 (ctng-1.21.0-229g-FA) ) #1 SMP PREEMPT Sat Nov 28 17:36:10 HKT 2015
[    0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine: NANOPI2
[    0.000000] Display: HDMI selected
[    0.000000] nxp_reserve_mem: reserve CMA: size 201326592
[    0.000000] NXP/CMA: Reserved 0x74000000/0x0c000000 for 'ion'
[    0.000000] NXP/CMA: success register cma region for 'ion'
[    0.000000] Memory policy: ECC disabled, Data cache writealloc
[    0.000000] CPU : iomap[ 0]: p 0xc0000000 -> v 0xf0000000 len=0x300000
[    0.000000] CPU : iomap[ 1]: p 0xf0000000 -> v 0xf0300000 len=0x100000
[    0.000000] CPU : iomap[ 2]: p 0xcf000000 -> v 0xf0400000 len=0x100000
[    0.000000] CPU : iomap[ 3]: p 0x2c000000 -> v 0xf0500000 len=0x100000
[    0.000000] CPU : iomap[ 4]: p 0x00000000 -> v 0xf0600000 len=0x100000
[    0.000000] CPU : DMA Zone Size =16M, CORE 4
[    0.000000] CPU : VERSION = 2 (0xE153000A), Assign Peripheral Exclusive Bus
[    0.000000] s5p4418-NanoPi2: Board initialized
[    0.000000] CPU : Clock Generator= 64 EA, DVFS = support, PLL.1
[    0.000000] PLL : [0] =  550000000, [1] = 1200000000, [2] =  800000000, [3] =  614399000
[    0.000000] PLL1: CPU FCLK = 1200000000, HCLK = 300000000
[    0.000000] PLL2: BUS BCLK =  400000000, PCLK = 200000000
[    0.000000] PLL2: MEM MCLK =  800000000, DCLK = 800000000, BCLK = 400000000, PCLK = 200000000
[    0.000000] PLL0: G3D BCLK =  550000000
[    0.000000] PLL2: MPG BCLK =  400000000, PCLK = 200000000
[    0.000000] PERCPU: Embedded 8 pages/cpu @81339000 s12288 r8192 d12288 u32768
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 259840
[    0.000000] Kernel command line: console=ttyAMA0,115200n8 root=/dev/mmcblk0p2 rootfstype=ext4 init=/sbin/init lcd=HDMI720P60
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] allocated 2097152 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.000000] Memory: 1024MB = 1024MB total
[    0.000000] Memory: 829296k/829296k available, 219280k reserved, 0K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xc0800000 - 0xfee00000   ( 998 MB)
[    0.000000]     lowmem  : 0x80000000 - 0xc0000000   (1024 MB)
[    0.000000]     pkmap   : 0x7fe00000 - 0x80000000   (   2 MB)
[    0.000000]     modules : 0x7f000000 - 0x7fe00000   (  14 MB)
[    0.000000]       .text : 0x80008000 - 0x808a9244   (8837 kB)
[    0.000000]       .init : 0x808aa000 - 0x808e1000   ( 220 kB)
[    0.000000]       .data : 0x808e2000 - 0x80953d78   ( 456 kB)
[    0.000000]        .bss : 0x80953d9c - 0x80a31840   ( 887 kB)
[    0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] NR_IRQS:288
[    0.000000] VIC @f0002000: id 0x00041192, vendor 0x41
[    0.000000] VIC @f0003000: id 0x00041192, vendor 0x41
[    0.000000] GPIO  @f001a000: start  64, mask 0xffffffff (gpio 53)
[    0.000000] GPIO  @f001b000: start  96, mask 0xffffffff (gpio 54)
[    0.000000] GPIO  @f001c000: start 128, mask 0xffffffff (gpio 55)
[    0.000000] GPIO  @f001d000: start 160, mask 0xffffffff (gpio 56)
[    0.000000] GPIO  @f001e000: start 192, mask 0xffffffff (gpio 57)
[    0.000000] ALIVE @f0010800: start 224, mask 0x000000ff (alive 4)
[    0.000000] GIC   @f0301000: start 256 (vic 31)
[    0.000000] timer.0: source,  10000000(HZ:250), mult:3355443200
[    0.000000] timer.1: event ,  10000000(HZ:250), mult:42949673
[    0.000000] sched_clock: 32 bits at 250 Hz, resolution 4000000ns, wraps every 4294967292ms
[    0.000000] Console: colour dummy device 80x30
[    0.000000] Calibrating delay loop... 2390.01 BogoMIPS (lpj=4780032)
[    0.036000] pid_max: default: 32768 minimum: 301
[    0.036000] Security Framework initialized
[    0.036000] SELinux:  Initializing.
[    0.036000] Mount-cache hash table entries: 512
[    0.036000] Initializing cgroup subsys debug
[    0.036000] Initializing cgroup subsys cpuacct
[    0.036000] Initializing cgroup subsys memory
[    0.036000] Initializing cgroup subsys freezer
[    0.036000] CPU: Testing write buffer coherency: ok
[    0.036000] CPU0: thread -1, cpu 0, socket 10, mpidr 80000a00
[    0.036000] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[    0.036000] Setting up static identity map for 0x4065e408 - 0x4065e460
[    0.036000] L310 cache controller enabled
[    0.036000] l2x0: 16 ways, CACHE_ID 0x4100c4c8, AUX_CTRL 0x70470001, Cache size: 1048576 B
[    0.076000] CPU1: thread -1, cpu 1, socket 10, mpidr 80000a01
[    0.108000] CPU2: thread -1, cpu 2, socket 10, mpidr 80000a02
[    0.140000] CPU3: thread -1, cpu 3, socket 10, mpidr 80000a03
[    0.140000] Brought up 4 CPUs
[    0.140000] SMP: Total of 4 processors activated (9560.06 BogoMIPS).
[    0.140000] devtmpfs: initialized
[    0.144000] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    0.144000] pwm: max = 50000000 hz
[    0.144000] prepare_gpio_suspend:
[    0.144000]   alfn[0][0]: 0x00000000, alfn[0][1]: 0x00000000
[    0.144000]   alfn[1][0]: 0x66800000, alfn[1][1]: 0x55555566
[    0.144000]   alfn[2][0]: 0x55555555, alfn[2][1]: 0x00555555
[    0.144000]   alfn[3][0]: 0x00000000, alfn[3][1]: 0x00000000
[    0.144000]   alfn[4][0]: 0x00000000, alfn[4][1]: 0x55540000
[    0.144000] dummy: 
[    0.144000] NET: Registered protocol family 16
[    0.144000] [Register machine platform devices]
[    0.144000] mach: add amba device uart-pl011.0 
[    0.144000] mach: add amba device uart-pl011.1 
[    0.144000] mach: add amba device pl08xdmac.0 
[    0.144000] mach: add amba device pl08xdmac.1 
[    0.144000] mach: add amba device ssp-pl022.0 
[    0.144000] mach: add device syncgen [2]
[    0.148000] mach: add device hdmi 
[    0.148000] mach: add device i2c bus (array:3) 
[    0.148000] mach: add device Real Time Clock  
[    0.148000] mach: add device generic pwm (array:1)
[    0.148000] mach: add device generic gpio (array:6)
[    0.148000] mach: add device i2s (array:1) 
[    0.148000] mach: add device spdif tx
[    0.148000] mach: add device usb_ehci
[    0.148000] mach: add device usb_ohci
[    0.148000] mach: add device usb otg
[    0.148000] mach: add device ion-nxp
[    0.148000] mach: add device adc
[    0.148000] mach: add graphic device opengl|es
[    0.148000] [Register board platform devices]
[    0.148000] plat: board revision 0
[    0.148000] plat: add dynamic frequency (pll.1)
[    0.148000] plat: add framebuffer
[    0.148000] plat: add device sdmmc [0]
[    0.148000] plat: add device sdmmc [1]
[    0.148000] plat: add device sdmmc [2]
[    0.148000] plat: add backlight pwm device
[    0.148000] plat: add device keypad
[    0.152000] plat: add device fixed voltage
[    0.152000] plat: add device spdif playback
[    0.152000] plat: add device nxp-v4l2
[    0.152000] plat: register spidev
[    0.152000] plat: add touch(ft5x0x) device
[    0.152000] plat: add device gpio_led
[    0.152000] 
[    0.152000] hw-breakpoint: Debug register access (0xee113e95) caused undefined instruction on CPU 1
[    0.152000] hw-breakpoint: Debug register access (0xee113e95) caused undefined instruction on CPU 2
[    0.152000] hw-breakpoint: Debug register access (0xee113e95) caused undefined instruction on CPU 3
[    0.152000] hw-breakpoint: CPU 2 debug is powered down!
[    0.152000] hw-breakpoint: CPU 3 debug is powered down!
[    0.152000] hw-breakpoint: CPU 1 debug is powered down!
[    0.152000] hw-breakpoint: Debug register access (0xee113e95) caused undefined instruction on CPU 0
[    0.152000] hw-breakpoint: CPU 0 debug is powered down!
[    0.152000] Serial: AMBA PL011 UART driver
[    0.152000] uart-pl011.0: ttyAMA0 at MMIO 0xc00a1000 (irq = 7) is a PL011 rev3
[    0.156000] console [ttyAMA0] enabled
[    0.160000] uart-pl011.1: ttyAMA1 at MMIO 0xc00a0000 (irq = 6) is a PL011 rev3
[    0.176000] bio: create slab <bio-0> at 0
[    0.180000] gpiochip_add: registered GPIOs 0 to 31 on device: nxp-gpio.0
[    0.184000] gpiochip_add: registered GPIOs 32 to 63 on device: nxp-gpio.1
[    0.188000] gpiochip_add: registered GPIOs 64 to 95 on device: nxp-gpio.2
[    0.192000] gpiochip_add: registered GPIOs 96 to 127 on device: nxp-gpio.3
[    0.196000] gpiochip_add: registered GPIOs 128 to 159 on device: nxp-gpio.4
[    0.200000] gpiochip_add: registered GPIOs 160 to 167 on device: nxp-gpio.5
[    0.204000] pl08xdmac pl08xdmac.0: Unbalanced pm_runtime_enable!
[    0.208000] pl08xdmac pl08xdmac.0: initialized 8 virtual memcpy channels
[    0.212000] pl08xdmac pl08xdmac.0: initialized 16 virtual slave channels
[    0.216000] pl08xdmac pl08xdmac.0: DMA: PL080 rev1 at 0xc0000000 irq 1
[    0.220000] pl08xdmac pl08xdmac.1: Unbalanced pm_runtime_enable!
[    0.224000] pl08xdmac pl08xdmac.1: initialized 8 virtual memcpy channels
[    0.228000] pl08xdmac pl08xdmac.1: initialized 15 virtual slave channels
[    0.236000] pl08xdmac pl08xdmac.1: DMA: PL080 rev1 at 0xc0001000 irq 2
[    0.240000] fixed_vdds: 1350 mV 
[    0.244000] nxp_ion_probe success!!!
[    0.248000] SCSI subsystem initialized
[    0.252000] ssp-pl022 ssp-pl022.0: ARM PL022 driver, device ID: 0x00041022
[    0.256000] pl022: mapped registers from 0xc005b000 to f005b000
[    0.260000] ssp-pl022 ssp-pl022.0: setup for DMA on RX dma1chan7, TX dma1chan6
[    0.264000] ssp-pl022 ssp-pl022.0: will use autosuspend for runtime pm, delay 10ms
[    0.268000] usbcore: registered new interface driver usbfs
[    0.272000] usbcore: registered new interface driver hub
[    0.276000] usbcore: registered new device driver usb
[    0.280000] nxp-i2c.0:   390625 hz [pclk=200000000, clk = 256, scale= 1, timeout= 500 ms]
[    0.288000] nxp-i2c.1:    97656 hz [pclk=200000000, clk = 256, scale= 7, timeout= 500 ms]
[    0.292000] nxp-i2c.2:   195312 hz [pclk=200000000, clk = 256, scale= 3, timeout= 500 ms]
[    0.296000] Linux media interface: v0.10
[    0.300000] Linux video capture interface: v2.00
[    0.304000] pps_core: LinuxPPS API ver. 1 registered
[    0.308000] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.312000] PTP clock support registered
[    0.316000] Advanced Linux Sound Architecture Driver Version 1.0.25.
[    0.320000] Bluetooth: Core ver 2.16
[    0.324000] NET: Registered protocol family 31
[    0.328000] Bluetooth: HCI device and connection manager initialized
[    0.332000] Bluetooth: HCI socket layer initialized
[    0.336000] Bluetooth: L2CAP socket layer initialized
[    0.340000] Bluetooth: SCO socket layer initialized
[    0.344000] cfg80211: Calling CRDA to update world regulatory domain
[    0.344000] Switching to clocksource source timer
[    0.364000] NET: Registered protocol family 2
[    0.368000] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.376000] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.384000] TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
[    0.392000] TCP: Hash tables configured (established 131072 bind 65536)
[    0.400000] TCP: reno registered
[    0.404000] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.408000] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.416000] NET: Registered protocol family 1
[    0.420000] RPC: Registered named UNIX socket transport module.
[    0.424000] RPC: Registered udp transport module.
[    0.432000] RPC: Registered tcp transport module.
[    0.436000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.440000] Disply Reset Status : On
[    0.472000] find cec header!_edid_find_target_cec_address: cec physical address 1000
[    0.480000] hdmi_get_edid_preset: preferred_preset is supported
[    0.484000] Display HDMI register operation 
[    0.488000] Display.0 fps=161 (6 ms), wait= 4 jiffies, Pixelclk=200000000hz
[    0.496000] bt_bcm: rfkill initialized
[    0.500000] audit: initializing netlink socket (disabled)
[    0.508000] type=2000 audit(0.508:1): initialized
[    0.516000] NFS: Registering the id_resolver key type
[    0.524000] fuse init (API version 7.18)
[    0.528000] msgmni has been set to 1619
[    0.532000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[    0.540000] io scheduler noop registered
[    0.544000] io scheduler deadline registered
[    0.548000] io scheduler cfq registered (default)
[    0.552000] display.0 connected to fb.0  ...
[    0.556000] nxp-fb.0: dma addr = 0x74000000, buf[0xb30c8400]
[    0.560000] nxp-fb.0: dma addr = 0x74384000, buf[0xb30c85c0]
[    0.624000] hdmi_stop entered
[    0.628000] hdmi_run entered
[    0.640000] HDMI PHY Ready!!!
[    0.644000] Display.0 fps=161 (6 ms), wait= 4 jiffies, Pixelclk=200000000hz
[    0.648000] _calc_hdmi_sync_param: _h_sync_offset 0
[    0.680000] hdmi_run exit
[    0.680000] nxp-fb 0: out[0], 1280 * 720 - 32 bpp (phys:74000000 virt:0xb4000000 max:7372800)
[    0.696000] uart-pl011 uart-pl011.0: no DMA platform data
[    0.700000] uart-pl011 uart-pl011.1: no DMA platform data
[    0.708000] loop: module loaded
[    0.712000] tun: Universal TUN/TAP device driver, 1.6
[    0.716000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    0.724000] PPP generic driver version 2.4.2
[    0.728000] PPP BSD Compression module registered
[    0.732000] PPP Deflate Compression module registered
[    0.736000] PPP MPPE Compression module registered
[    0.740000] NET: Registered protocol family 24
[    0.748000] usbcore: registered new interface driver asix
[    0.752000] usbcore: registered new interface driver cdc_ether
[    0.756000] usbcore: registered new interface driver net1080
[    0.764000] usbcore: registered new interface driver cdc_subset
[    0.768000] usbcore: registered new interface driver zaurus
[    0.776000] usbcore: registered new interface driver cdc_ncm
[    0.780000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.788000] nxp-ehci nxp-ehci: SLsi Synopsys EHCI Host Controller
[    0.792000] nxp-ehci nxp-ehci: new USB bus registered, assigned bus number 1
[    0.800000] nxp-ehci nxp-ehci: irq 50, io mem 0xc0030000
[    0.816000] nxp-ehci nxp-ehci: USB 0.0 started, EHCI 1.00
[    0.820000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    0.828000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.832000] usb usb1: Product: SLsi Synopsys EHCI Host Controller
[    0.840000] usb usb1: Manufacturer: Linux 3.4.39-FriendlyARM ehci_hcd
[    0.848000] usb usb1: SerialNumber: nxp-ehci
[    0.852000] hub 1-0:1.0: USB hub found
[    0.856000] hub 1-0:1.0: 3 ports detected
[    0.860000] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[    1.064000] Core Release: 2.93a
[    1.068000] Setting default values for core params
[    1.072000] Finished setting default values for core params
[    1.276000] Using Descriptor DMA mode
[    1.280000] Dedicated Tx FIFOs mode
[    1.284000] dwc_otg dwc_otg: DWC OTG Controller
[    1.288000] dwc_otg dwc_otg: new USB bus registered, assigned bus number 2
[    1.296000] dwc_otg dwc_otg: irq 49, io mem 0x00000000
[    1.300000] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    1.308000] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.316000] usb usb2: Product: DWC OTG Controller
[    1.320000] usb usb2: Manufacturer: Linux 3.4.39-FriendlyARM dwc_otg_hcd
[    1.328000] usb usb2: SerialNumber: dwc_otg
[    1.332000] hub 2-0:1.0: USB hub found
[    1.336000] hub 2-0:1.0: 1 port detected
[    1.340000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.344000] nxp-ohci nxp-ohci: SLsi Synopsys OHCI Host Controller
[    1.352000] nxp-ohci nxp-ohci: new USB bus registered, assigned bus number 3
[    1.360000] nxp-ohci nxp-ohci: irq 50, io mem 0xc0020000
[    1.424000] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[    1.428000] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.436000] usb usb3: Product: SLsi Synopsys OHCI Host Controller
[    1.444000] HDMI HPD State 0x1
[    1.444000] usb usb3: Manufacturer: Linux 3.4.39-FriendlyARM ohci_hcd
[    1.452000] usb usb3: SerialNumber: nxp-ohci
[    1.456000] hub 3-0:1.0: USB hub found
[    1.460000] hub 3-0:1.0: 3 ports detected
[    1.464000] Initializing USB Mass Storage driver...
[    1.468000] usbcore: registered new interface driver usb-storage
[    1.476000] USB Mass Storage support registered.
[    1.480000] android_usb gadget: Mass Storage Function, version: 2009/09/11
[    1.488000] android_usb gadget: Number of LUNs=1
[    1.492000]  lun0: LUN: removable file: (no medium)
[    1.496000] find cec header!_edid_find_target_cec_address: cec physical address 1000
[    1.500000] android_usb gadget: android_usb ready
[    1.500000] mousedev: PS/2 mouse device common for all mice
[    1.500000] input: Nexell Keypad as /devices/platform/nxp-keypad/input/input0
[    1.500000] usbcore: registered new interface driver xpad
[    1.500000] input: ft5x0x_ts as /devices/virtual/input/input1
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:1)
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:2)
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:3)
[    1.508000] Error: i2c.2, addr:70, trans len:-11(1), try:3
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:1)
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:2)
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:3)
[    1.508000] Error: i2c.2, addr:70, trans len:-11(1), try:3
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:1)
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:2)
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:3)
[    1.508000] Error: i2c.2, addr:70, trans len:-11(1), try:3
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:1)
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:2)
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:3)
[    1.508000] Error: i2c.2, addr:70, trans len:-11(1), try:3
[    1.508000] read reg (0xa6) error, -11
[    1.508000] ft5x0x_ts 2-0038: chip not found
[    1.680000] _hdmi_hpd_changed: edid update success, preset 18
[    1.684000] notify_hpd_changed: state 1
[    1.688000] hdmi_run entered
[    1.692000] hdmi_run: hdmi already running!
[    1.740000] ft5x0x_ts 2-0038: probe ft5x0x TouchScreen failed, -11
[    1.744000] ft5x0x_ts: probe of 2-0038 failed with error -11
[    1.752000] [RTC] day=2009.09.01 time=00:00:00
[    1.756000] nxp-rtc nxp-rtc.0: rtc core: registered nxp-rtc as rtc0
[    1.760000] i2c /dev entries driver
[    1.764000] gspca_main: v2.14.0 registered
[    1.772000] usbcore: registered new interface driver uvcvideo
[    1.776000] USB Video Class driver (1.1.1)
[    1.780000] device-mapper: uevent: version 1.0.3
[    1.788000] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
[    1.796000] Bluetooth: HCI UART driver ver 2.2
[    1.800000] Bluetooth: HCI H4 protocol initialized
[    1.804000] DVFS: ASV[0] IDS(10mA, 10) Ro(110, 95)
[    1.808000] ASV  0 =  1400000khz,  1350000 uV 
[    1.812000] ASV  1 =  1200000khz,  1250000 uV 
[    1.816000] ASV  2 =  1000000khz,  1175000 uV 
[    1.824000] ASV  3 =   800000khz,  1125000 uV 
[    1.828000] ASV  4 =   700000khz,  1100000 uV 
[    1.832000] ASV  5 =   600000khz,  1075000 uV 
[    1.836000] ASV  6 =   500000khz,  1075000 uV 
[    1.840000] ASV  7 =   400000khz,  1075000 uV 
[    1.844000] DVFS: regulator vdd_arm_1.3V
[    1.848000] DVFS: cpu DVFS with PLL.1 [tables=8]
[    1.856000] cpuidle: using governor ladder
[    1.860000] cpuidle: using governor menu
[    1.864000] Synopsys Designware Multimedia Card Interface Driver
[    1.868000] dw_mmc dw_mmc.0: Using internal DMA controller.
[    1.876000] Unable to handle kernel paging request at virtual address 60000112
[    1.876000] mmc0: no vmmc regulator found
[    1.876000] dw_mmc dw_mmc.0: Using external card detect irq 225 (io 161)
[    1.876000] dw_mmc dw_mmc.0: Version ID is 250a
[    1.876000] dw_mmc dw_mmc.0: DW MMC controller at irq 43, 32 bit host data width, 32 deep fifo hw timeout 500 ms
[    1.876000] dw_mmc dw_mmc.1: Using PIO mode.
[    1.876000] mmc1: no vmmc regulator found
[    1.876000] dw_mmc dw_mmc.1: Version ID is 250a
[    1.876000] dw_mmc dw_mmc.1: DW MMC controller at irq 44, 32 bit host data width, 32 deep fifo hw timeout 500 ms
[    1.876000] dw_mmc dw_mmc.2: Using internal DMA controller.
[    1.876000] mmc2: no vmmc regulator found
[    1.876000] dw_mmc dw_mmc.2: Using external card detect irq 152 (io 88)
[    1.876000] dw_mmc dw_mmc.2: Version ID is 250a
[    1.876000] dw_mmc dw_mmc.2: DW MMC controller at irq 45, 32 bit host data width, 32 deep fifo hw timeout 500 ms
[    1.960000] pgd = 80004000
[    1.964000] [60000112] *pgd=00000000
[    1.968000] Internal error: Oops: 80000005 [#1] PREEMPT SMP ARM
[    1.972000] Modules linked in:
[    1.976000] CPU: 2    Not tainted  (3.4.39-FriendlyARM #1)
[    1.980000] PC is at 0x60000112
[    1.984000] LR is at trigger_load_balance+0x2ec/0x390
[    1.988000] pc : [<60000112>]    lr : [<8007b9d8>]    psr: 600001b3
[    1.988000] sp : b3a4dc08  ip : 00000000  fp : 8090e8c0
[    2.000000] r10: 8008e858  r9 : b3a4dda8  r8 : 00000002
[    2.008000] r7 : 00000000  r6 : 74ed4533  r5 : 00000000  r4 : 00000000
[    2.012000] r3 : 74eda677  r2 : 00000000  r1 : 8134b8f0  r0 : 00000000
[    2.020000] Flags: nZCv  IRQs off  FIQs on  Mode SVC_32  ISA Thumb  Segment kernel
[    2.028000] Control: 10c5387d  Table: 4000404a  DAC: 00000015
[    2.032000] 
[    2.032000] LR: 0x8007b958:
[    2.036000] b958  e19c1f9f e2811001 e18c0f91 e3300000 1afffffa e5922000 e3520000 1afffff4
[    2.044000] b978  eb010df0 eaffff80 e5933000 e3530000 0affffcf e5932038 e3120c01 1affffbb
--------------------------------------------------------------------------------
 Second Boot by Nexell Co. : Built on Nov 19 2014 20:10:38
--------------------------------------------------------------------------------
 PLL0: 550000000   PLL1: 1200000000   PLL2: 800000000   PLL3: 612000000

 Divider0 PLL: 1 CPU:1200000000   CPU BUS:300000000
 Divider1 PLL: 2 BCLK:400000000   PCLK:200000000
 Divider2 PLL: 2 MDCLK:800000000   MCLK:800000000   
		 MBCLK:400000000   MPCLK:200000000
 Divider3 PLL: 0 G3D BCLK:550000000
 Divider4 PLL: 2 MPEG BCLK:400000000   MPEG PCLK:200000000

123
DDR3 POR Init Start
phy init

########## READ/GATE Level ##########
DDR3 Init Done!
Loading from sdmmc...
 Image Loading Done!
Launch to 0x42C00000


U-Boot 2014.07-gd46d757 (Nov 27 2015 - 17:09:12)

PLL : [0] =  550000000, [1] = 1200000000, [2] =  800000000, [3] =  614399000
PLL1: CPU FCLK = 1200000000, HCLK = 300000000
PLL2: BUS BCLK =  400000000, PCLK = 200000000
PLL2: MEM MCLK =  800000000, DCLK = 800000000, BCLK = 400000000, PCLK = 200000000
PLL0: G3D BCLK =  550000000
PLL2: MPG BCLK =  400000000, PCLK = 200000000
I2C:   ready
DRAM:  256 MiB
Heap = 0x43000000~0x45000000
Code = 0x42c00000~0x42c72984
GLD  = 0x42bffeb8
GLBD = 0x42bffe68
SP   = 0x42bffe68,0x42bffe50(CURR)
PC   = 0x42c06114
TAGS = 0x40000100 
PAGE = 0x42c80000~0x42c8c000
MACH = [4330]   
VER  = 1      
BOARD= [nanopi2]    
LCD  = N/A (-1)
MMC:   NXP DWMMC: 0, NXP DWMMC: 1, NXP DWMMC: 2
In:    serial
Out:   serial
Err:   serial
switch to partitions #0, OK
mmc0 is current device
Writing to MMC(0)... done
HDMI: display.0, preset 0 (1280 *  720)
HDMI: PHY Ready!!!
DONE: Logo bmp 800 by 480 (3bpp), len=1152056 

DRAW: 0x47000000 -> 0x46000000 

Hit any key to stop autoboot:  1  0 
## Booting kernel from Legacy Image at 48000000 ...
   Image Name:   Linux-3.4.39-FriendlyARM
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4767712 Bytes = 4.5 MiB
   Load Address: 40008000
   Entry Point:  40008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 3.4.39-FriendlyARM (root@jensen) (gcc version 4.9.3 (ctng-1.21.0-229g-FA) ) #1 SMP PREEMPT Sat Nov 28 17:36:10 HKT 2015
[    0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine: NANOPI2
[    0.000000] Display: HDMI selected
[    0.000000] nxp_reserve_mem: reserve CMA: size 201326592
[    0.000000] NXP/CMA: Reserved 0x74000000/0x0c000000 for 'ion'
[    0.000000] NXP/CMA: success register cma region for 'ion'
[    0.000000] Memory policy: ECC disabled, Data cache writealloc
[    0.000000] CPU : iomap[ 0]: p 0xc0000000 -> v 0xf0000000 len=0x300000
[    0.000000] CPU : iomap[ 1]: p 0xf0000000 -> v 0xf0300000 len=0x100000
[    0.000000] CPU : iomap[ 2]: p 0xcf000000 -> v 0xf0400000 len=0x100000
[    0.000000] CPU : iomap[ 3]: p 0x2c000000 -> v 0xf0500000 len=0x100000
[    0.000000] CPU : iomap[ 4]: p 0x00000000 -> v 0xf0600000 len=0x100000
[    0.000000] CPU : DMA Zone Size =16M, CORE 4
[    0.000000] CPU : VERSION = 2 (0xE153000A), Assign Peripheral Exclusive Bus
[    0.000000] s5p4418-NanoPi2: Board initialized
[    0.000000] CPU : Clock Generator= 64 EA, DVFS = support, PLL.1
[    0.000000] PLL : [0] =  550000000, [1] = 1200000000, [2] =  800000000, [3] =  614399000
[    0.000000] PLL1: CPU FCLK = 1200000000, HCLK = 300000000
[    0.000000] PLL2: BUS BCLK =  400000000, PCLK = 200000000
[    0.000000] PLL2: MEM MCLK =  800000000, DCLK = 800000000, BCLK = 400000000, PCLK = 200000000
[    0.000000] PLL0: G3D BCLK =  550000000
[    0.000000] PLL2: MPG BCLK =  400000000, PCLK = 200000000
[    0.000000] PERCPU: Embedded 8 pages/cpu @81339000 s12288 r8192 d12288 u32768
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 259840
[    0.000000] Kernel command line: console=ttyAMA0,115200n8 root=/dev/mmcblk0p2 rootfstype=ext4 init=/sbin/init lcd=HDMI720P60
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] allocated 2097152 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.000000] Memory: 1024MB = 1024MB total
[    0.000000] Memory: 829296k/829296k available, 219280k reserved, 0K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xc0800000 - 0xfee00000   ( 998 MB)
[    0.000000]     lowmem  : 0x80000000 - 0xc0000000   (1024 MB)
[    0.000000]     pkmap   : 0x7fe00000 - 0x80000000   (   2 MB)
[    0.000000]     modules : 0x7f000000 - 0x7fe00000   (  14 MB)
[    0.000000]       .text : 0x80008000 - 0x808a9244   (8837 kB)
[    0.000000]       .init : 0x808aa000 - 0x808e1000   ( 220 kB)
[    0.000000]       .data : 0x808e2000 - 0x80953d78   ( 456 kB)
[    0.000000]        .bss : 0x80953d9c - 0x80a31840   ( 887 kB)
[    0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] NR_IRQS:288
[    0.000000] VIC @f0002000: id 0x00041192, vendor 0x41
[    0.000000] VIC @f0003000: id 0x00041192, vendor 0x41
[    0.000000] GPIO  @f001a000: start  64, mask 0xffffffff (gpio 53)
[    0.000000] GPIO  @f001b000: start  96, mask 0xffffffff (gpio 54)
[    0.000000] GPIO  @f001c000: start 128, mask 0xffffffff (gpio 55)
[    0.000000] GPIO  @f001d000: start 160, mask 0xffffffff (gpio 56)
[    0.000000] GPIO  @f001e000: start 192, mask 0xffffffff (gpio 57)
[    0.000000] ALIVE @f0010800: start 224, mask 0x000000ff (alive 4)
[    0.000000] GIC   @f0301000: start 256 (vic 31)
[    0.000000] timer.0: source,  10000000(HZ:250), mult:3355443200
[    0.000000] timer.1: event ,  10000000(HZ:250), mult:42949673
[    0.000000] sched_clock: 32 bits at 250 Hz, resolution 4000000ns, wraps every 4294967292ms
[    0.000000] Console: colour dummy device 80x30
[    0.000000] Calibrating delay loop... 2390.01 BogoMIPS (lpj=4780032)
[    0.036000] pid_max: default: 32768 minimum: 301
[    0.036000] Security Framework initialized
[    0.036000] SELinux:  Initializing.
[    0.036000] Mount-cache hash table entries: 512
[    0.036000] Initializing cgroup subsys debug
[    0.036000] Initializing cgroup subsys cpuacct
[    0.036000] Initializing cgroup subsys memory
[    0.036000] Initializing cgroup subsys freezer
[    0.036000] CPU: Testing write buffer coherency: ok
[    0.036000] CPU0: thread -1, cpu 0, socket 10, mpidr 80000a00
[    0.036000] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[    0.036000] Setting up static identity map for 0x4065e408 - 0x4065e460
[    0.036000] L310 cache controller enabled
[    0.036000] l2x0: 16 ways, CACHE_ID 0x4100c4c8, AUX_CTRL 0x70470001, Cache size: 1048576 B
[    0.076000] CPU1: thread -1, cpu 1, socket 10, mpidr 80000a01
[    0.108000] CPU2: thread -1, cpu 2, socket 10, mpidr 80000a02
[    0.140000] CPU3: thread -1, cpu 3, socket 10, mpidr 80000a03
[    0.140000] Brought up 4 CPUs
[    0.140000] SMP: Total of 4 processors activated (9560.06 BogoMIPS).
[    0.140000] devtmpfs: initialized
[    0.144000] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    0.144000] pwm: max = 50000000 hz
[    0.144000] prepare_gpio_suspend:
[    0.144000]   alfn[0][0]: 0x00000000, alfn[0][1]: 0x00000000
[    0.144000]   alfn[1][0]: 0x66800000, alfn[1][1]: 0x55555566
[    0.144000]   alfn[2][0]: 0x55555555, alfn[2][1]: 0x00555555
[    0.144000]   alfn[3][0]: 0x00000000, alfn[3][1]: 0x00000000
[    0.144000]   alfn[4][0]: 0x00000000, alfn[4][1]: 0x55540000
[    0.144000] dummy: 
[    0.144000] NET: Registered protocol family 16
[    0.144000] [Register machine platform devices]
[    0.144000] mach: add amba device uart-pl011.0 
[    0.144000] mach: add amba device uart-pl011.1 
[    0.144000] mach: add amba device pl08xdmac.0 
[    0.144000] mach: add amba device pl08xdmac.1 
[    0.144000] mach: add amba device ssp-pl022.0 
[    0.144000] mach: add device syncgen [2]
[    0.148000] mach: add device hdmi 
[    0.148000] mach: add device i2c bus (array:3) 
[    0.148000] mach: add device Real Time Clock  
[    0.148000] mach: add device generic pwm (array:1)
[    0.148000] mach: add device generic gpio (array:6)
[    0.148000] mach: add device i2s (array:1) 
[    0.148000] mach: add device spdif tx
[    0.148000] mach: add device usb_ehci
[    0.148000] mach: add device usb_ohci
[    0.148000] mach: add device usb otg
[    0.148000] mach: add device ion-nxp
[    0.148000] mach: add device adc
[    0.148000] mach: add graphic device opengl|es
[    0.148000] [Register board platform devices]
[    0.148000] plat: board revision 0
[    0.148000] plat: add dynamic frequency (pll.1)
[    0.148000] plat: add framebuffer
[    0.148000] plat: add device sdmmc [0]
[    0.148000] plat: add device sdmmc [1]
[    0.148000] plat: add device sdmmc [2]
[    0.148000] plat: add backlight pwm device
[    0.148000] plat: add device keypad
[    0.152000] plat: add device fixed voltage
[    0.152000] plat: add device spdif playback
[    0.152000] plat: add device nxp-v4l2
[    0.152000] plat: register spidev
[    0.152000] plat: add touch(ft5x0x) device
[    0.152000] plat: add device gpio_led
[    0.152000] 
[    0.152000] hw-breakpoint: Debug register access (0xee113e95) caused undefined instruction on CPU 1
[    0.152000] hw-breakpoint: Debug register access (0xee113e95) caused undefined instruction on CPU 2
[    0.152000] hw-breakpoint: Debug register access (0xee113e95) caused undefined instruction on CPU 3
[    0.152000] hw-breakpoint: CPU 2 debug is powered down!
[    0.152000] hw-breakpoint: CPU 3 debug is powered down!
[    0.152000] hw-breakpoint: CPU 1 debug is powered down!
[    0.152000] hw-breakpoint: Debug register access (0xee113e95) caused undefined instruction on CPU 0
[    0.152000] hw-breakpoint: CPU 0 debug is powered down!
[    0.152000] Serial: AMBA PL011 UART driver
[    0.152000] uart-pl011.0: ttyAMA0 at MMIO 0xc00a1000 (irq = 7) is a PL011 rev3
[    0.156000] console [ttyAMA0] enabled
[    0.160000] uart-pl011.1: ttyAMA1 at MMIO 0xc00a0000 (irq = 6) is a PL011 rev3
[    0.176000] bio: create slab <bio-0> at 0
[    0.180000] gpiochip_add: registered GPIOs 0 to 31 on device: nxp-gpio.0
[    0.184000] gpiochip_add: registered GPIOs 32 to 63 on device: nxp-gpio.1
[    0.188000] gpiochip_add: registered GPIOs 64 to 95 on device: nxp-gpio.2
[    0.192000] gpiochip_add: registered GPIOs 96 to 127 on device: nxp-gpio.3
[    0.196000] gpiochip_add: registered GPIOs 128 to 159 on device: nxp-gpio.4
[    0.200000] gpiochip_add: registered GPIOs 160 to 167 on device: nxp-gpio.5
[    0.204000] pl08xdmac pl08xdmac.0: Unbalanced pm_runtime_enable!
[    0.208000] pl08xdmac pl08xdmac.0: initialized 8 virtual memcpy channels
[    0.212000] pl08xdmac pl08xdmac.0: initialized 16 virtual slave channels
[    0.216000] pl08xdmac pl08xdmac.0: DMA: PL080 rev1 at 0xc0000000 irq 1
[    0.220000] pl08xdmac pl08xdmac.1: Unbalanced pm_runtime_enable!
[    0.224000] pl08xdmac pl08xdmac.1: initialized 8 virtual memcpy channels
[    0.228000] pl08xdmac pl08xdmac.1: initialized 15 virtual slave channels
[    0.236000] pl08xdmac pl08xdmac.1: DMA: PL080 rev1 at 0xc0001000 irq 2
[    0.240000] fixed_vdds: 1350 mV 
[    0.244000] nxp_ion_probe success!!!
[    0.248000] SCSI subsystem initialized
[    0.252000] ssp-pl022 ssp-pl022.0: ARM PL022 driver, device ID: 0x00041022
[    0.256000] pl022: mapped registers from 0xc005b000 to f005b000
[    0.260000] ssp-pl022 ssp-pl022.0: setup for DMA on RX dma1chan7, TX dma1chan6
[    0.264000] ssp-pl022 ssp-pl022.0: will use autosuspend for runtime pm, delay 10ms
[    0.268000] usbcore: registered new interface driver usbfs
[    0.272000] usbcore: registered new interface driver hub
[    0.276000] usbcore: registered new device driver usb
[    0.280000] nxp-i2c.0:   390625 hz [pclk=200000000, clk = 256, scale= 1, timeout= 500 ms]
[    0.288000] nxp-i2c.1:    97656 hz [pclk=200000000, clk = 256, scale= 7, timeout= 500 ms]
[    0.292000] nxp-i2c.2:   195312 hz [pclk=200000000, clk = 256, scale= 3, timeout= 500 ms]
[    0.296000] Linux media interface: v0.10
[    0.300000] Linux video capture interface: v2.00
[    0.304000] pps_core: LinuxPPS API ver. 1 registered
[    0.308000] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.312000] PTP clock support registered
[    0.316000] Advanced Linux Sound Architecture Driver Version 1.0.25.
[    0.320000] Bluetooth: Core ver 2.16
[    0.324000] NET: Registered protocol family 31
[    0.328000] Bluetooth: HCI device and connection manager initialized
[    0.332000] Bluetooth: HCI socket layer initialized
[    0.336000] Bluetooth: L2CAP socket layer initialized
[    0.340000] Bluetooth: SCO socket layer initialized
[    0.344000] cfg80211: Calling CRDA to update world regulatory domain
[    0.344000] Switching to clocksource source timer
[    0.364000] NET: Registered protocol family 2
[    0.368000] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.376000] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.384000] TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
[    0.392000] TCP: Hash tables configured (established 131072 bind 65536)
[    0.400000] TCP: reno registered
[    0.404000] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.408000] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.416000] NET: Registered protocol family 1
[    0.420000] RPC: Registered named UNIX socket transport module.
[    0.424000] RPC: Registered udp transport module.
[    0.432000] RPC: Registered tcp transport module.
[    0.436000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.440000] Disply Reset Status : On
[    0.472000] find cec header!_edid_find_target_cec_address: cec physical address 1000
[    0.480000] hdmi_get_edid_preset: preferred_preset is supported
[    0.484000] Display HDMI register operation 
[    0.488000] Display.0 fps=161 (6 ms), wait= 4 jiffies, Pixelclk=200000000hz
[    0.496000] bt_bcm: rfkill initialized
[    0.500000] audit: initializing netlink socket (disabled)
[    0.508000] type=2000 audit(0.508:1): initialized
[    0.516000] NFS: Registering the id_resolver key type
[    0.524000] fuse init (API version 7.18)
[    0.528000] msgmni has been set to 1619
[    0.532000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[    0.540000] io scheduler noop registered
[    0.544000] io scheduler deadline registered
[    0.548000] io scheduler cfq registered (default)
[    0.552000] display.0 connected to fb.0  ...
[    0.556000] nxp-fb.0: dma addr = 0x74000000, buf[0xb30c8400]
[    0.560000] nxp-fb.0: dma addr = 0x74384000, buf[0xb30c85c0]
[    0.624000] hdmi_stop entered
[    0.628000] hdmi_run entered
[    0.640000] HDMI PHY Ready!!!
[    0.644000] Display.0 fps=161 (6 ms), wait= 4 jiffies, Pixelclk=200000000hz
[    0.648000] _calc_hdmi_sync_param: _h_sync_offset 0
[    0.680000] hdmi_run exit
[    0.680000] nxp-fb 0: out[0], 1280 * 720 - 32 bpp (phys:74000000 virt:0xb4000000 max:7372800)
[    0.696000] uart-pl011 uart-pl011.0: no DMA platform data
[    0.700000] uart-pl011 uart-pl011.1: no DMA platform data
[    0.708000] loop: module loaded
[    0.712000] tun: Universal TUN/TAP device driver, 1.6
[    0.716000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    0.724000] PPP generic driver version 2.4.2
[    0.728000] PPP BSD Compression module registered
[    0.732000] PPP Deflate Compression module registered
[    0.736000] PPP MPPE Compression module registered
[    0.740000] NET: Registered protocol family 24
[    0.748000] usbcore: registered new interface driver asix
[    0.752000] usbcore: registered new interface driver cdc_ether
[    0.756000] usbcore: registered new interface driver net1080
[    0.764000] usbcore: registered new interface driver cdc_subset
[    0.768000] usbcore: registered new interface driver zaurus
[    0.776000] usbcore: registered new interface driver cdc_ncm
[    0.780000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.788000] nxp-ehci nxp-ehci: SLsi Synopsys EHCI Host Controller
[    0.792000] nxp-ehci nxp-ehci: new USB bus registered, assigned bus number 1
[    0.800000] nxp-ehci nxp-ehci: irq 50, io mem 0xc0030000
[    0.816000] nxp-ehci nxp-ehci: USB 0.0 started, EHCI 1.00
[    0.820000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    0.828000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.832000] usb usb1: Product: SLsi Synopsys EHCI Host Controller
[    0.840000] usb usb1: Manufacturer: Linux 3.4.39-FriendlyARM ehci_hcd
[    0.848000] usb usb1: SerialNumber: nxp-ehci
[    0.852000] hub 1-0:1.0: USB hub found
[    0.856000] hub 1-0:1.0: 3 ports detected
[    0.860000] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[    1.064000] Core Release: 2.93a
[    1.068000] Setting default values for core params
[    1.072000] Finished setting default values for core params
[    1.276000] Using Descriptor DMA mode
[    1.280000] Dedicated Tx FIFOs mode
[    1.284000] dwc_otg dwc_otg: DWC OTG Controller
[    1.288000] dwc_otg dwc_otg: new USB bus registered, assigned bus number 2
[    1.296000] dwc_otg dwc_otg: irq 49, io mem 0x00000000
[    1.300000] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    1.308000] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.316000] usb usb2: Product: DWC OTG Controller
[    1.320000] usb usb2: Manufacturer: Linux 3.4.39-FriendlyARM dwc_otg_hcd
[    1.328000] usb usb2: SerialNumber: dwc_otg
[    1.332000] hub 2-0:1.0: USB hub found
[    1.336000] hub 2-0:1.0: 1 port detected
[    1.340000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.344000] nxp-ohci nxp-ohci: SLsi Synopsys OHCI Host Controller
[    1.352000] nxp-ohci nxp-ohci: new USB bus registered, assigned bus number 3
[    1.360000] nxp-ohci nxp-ohci: irq 50, io mem 0xc0020000
[    1.424000] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[    1.428000] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.436000] usb usb3: Product: SLsi Synopsys OHCI Host Controller
[    1.444000] HDMI HPD State 0x1
[    1.444000] usb usb3: Manufacturer: Linux 3.4.39-FriendlyARM ohci_hcd
[    1.452000] usb usb3: SerialNumber: nxp-ohci
[    1.456000] hub 3-0:1.0: USB hub found
[    1.460000] hub 3-0:1.0: 3 ports detected
[    1.464000] Initializing USB Mass Storage driver...
[    1.468000] usbcore: registered new interface driver usb-storage
[    1.476000] USB Mass Storage support registered.
[    1.480000] android_usb gadget: Mass Storage Function, version: 2009/09/11
[    1.488000] android_usb gadget: Number of LUNs=1
[    1.492000]  lun0: LUN: removable file: (no medium)
[    1.496000] find cec header!_edid_find_target_cec_address: cec physical address 1000
[    1.500000] android_usb gadget: android_usb ready
[    1.500000] mousedev: PS/2 mouse device common for all mice
[    1.500000] input: Nexell Keypad as /devices/platform/nxp-keypad/input/input0
[    1.500000] usbcore: registered new interface driver xpad
[    1.500000] input: ft5x0x_ts as /devices/virtual/input/input1
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:1)
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:2)
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:3)
[    1.508000] Error: i2c.2, addr:70, trans len:-11(1), try:3
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:1)
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:2)
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:3)
[    1.508000] Error: i2c.2, addr:70, trans len:-11(1), try:3
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:1)
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:2)
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:3)
[    1.508000] Error: i2c.2, addr:70, trans len:-11(1), try:3
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:1)
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:2)
[    1.508000] Fail, noack i2c.2 addr [0x70] data[0x70], trans[ 0: 1]
[    1.508000] i2c.2 addr 0x70 (try:3)
[    1.508000] Error: i2c.2, addr:70, trans len:-11(1), try:3
[    1.508000] read reg (0xa6) error, -11
[    1.508000] ft5x0x_ts 2-0038: chip not found
[    1.680000] _hdmi_hpd_changed: edid update success, preset 18
[    1.684000] notify_hpd_changed: state 1
[    1.688000] hdmi_run entered
[    1.692000] hdmi_run: hdmi already running!
[    1.720000] ft5x0x_ts 2-0038: probe ft5x0x TouchScreen failed, -11
[    1.724000] ft5x0x_ts: probe of 2-0038 failed with error -11
[    1.732000] [RTC] day=2009.09.01 time=00:00:00
[    1.736000] nxp-rtc nxp-rtc.0: rtc core: registered nxp-rtc as rtc0
[    1.740000] i2c /dev entries driver
[    1.744000] gspca_main: v2.14.0 registered
[    1.752000] usbcore: registered new interface driver uvcvideo
[    1.756000] USB Video Class driver (1.1.1)
[    1.760000] device-mapper: uevent: version 1.0.3
[    1.768000] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
[    1.776000] Bluetooth: HCI UART driver ver 2.2
[    1.780000] Bluetooth: HCI H4 protocol initialized
[    1.784000] DVFS: ASV[0] IDS(10mA, 10) Ro(110, 95)
[    1.788000] ASV  0 =  1400000khz,  1350000 uV 
[    1.792000] ASV  1 =  1200000khz,  1250000 uV 
[    1.796000] ASV  2 =  1000000khz,  1175000 uV 
[    1.804000] ASV  3 =   800000khz,  1125000 uV 
[    1.808000] ASV  4 =   700000khz,  1100000 uV 
[    1.812000] ASV  5 =   600000khz,  1075000 uV 
[    1.816000] ASV  6 =   500000khz,  1075000 uV 
[    1.820000] ASV  7 =   400000khz,  1075000 uV 
[    1.824000] DVFS: regulator vdd_arm_1.3V
[    1.828000] DVFS: cpu DVFS with PLL.1 [tables=8]
[    1.836000] cpuidle: using governor ladder
[    1.840000] cpuidle: using governor menu
[    1.844000] Synopsys Designware Multimedia Card Interface Driver
[    1.848000] dw_mmc dw_mmc.0: Using internal DMA controller.
[    1.856000] mmc0: no vmmc regulator found
[    1.856000] Unable to handle kernel NULL pointer dereference at virtual address 000001f1
0000009
[    1.868000]  e5911000
[    1.868000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
00009
[    1.876000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
ble to handle kernel NULL pointer dereference at virtual address 00000009
[    1.884000] pgd = 00000009
 dereference at virtual address 00000009
[    1.892000] pgd = 00000009
[    1.892000] Unable to handle kernel NULL p 1.904000] pgd = 00000009
<1>[    1.904000] Unable to handle kernel NULL pointer dereference at virtual ad  1.912000] Unable to handle kernel NULL pointer dereference at virtual address 000001f1
tual address 00000009
[    1.920000] Unable to handle kernel paging request at virtual address 39323054
32000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] Unable to handle kernel paging request at virtual address 39333254
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 000001f1
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 000001f1
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 000001f1
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] Unable to handle kernel paging request at virtual address 000186c3
[    1.932000] pgd = 800196c8
[    1.932000] [000186c3] *pgd=e59871ec
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 000001f1
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] pgd = 00000009
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.932000] Unable to handle kernel paging request at virtual address 39333254
[    1.932000] Unable to handle kernel NULL pointer dereference at virtual address 000001f1
 NULL pointer dereference at virtual address 00000009
[    1.924000] pgd = 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.924000] pgd = 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.924000] pgd = 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.924000] pgd = 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.924000] pgd = 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.924000] pgd = 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.924000] pgd = 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.924000] pgd = 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.924000] pgd = 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.924000] pgd = 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.924000] pgd = 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.924000] pgd = 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.924000] pgd = 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.924000] pgd = 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.924000] pgd = 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.924000] pgd = 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.924000] pgd = 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 000001f1
[    1.924000] pgd = 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.924000] pgd = 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.924000] pgd = 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.924000] pgd = 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.924000] pgd = 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.924000] pgd = 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.924000] pgd = 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.924000] pgd = 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.924000] pgd = 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.924000] pgd = 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.924000] pgd = 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.924000] pgd = 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.924000] pgd = 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.924000] pgd = 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.924000] pgd = 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.924000] pgd = 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.924000] pgd = 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.924000] pgd = 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.924000] pgd = 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 000001f1
[    1.924000] pgd = 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.924000] pgd = 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.924000] pgd = 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.924000] pgd = 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.924000] pgd = 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.924000] pgd = 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.924000] pgd = 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.924000] pgd = 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.924000] pgd = 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.924000] pgd = 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.924000] pgd = 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.924000] pgd = 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.924000] pgd = 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.924000] pgd = 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.924000] pgd = 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.924000] pgd = 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.924000] pgd = 00000009
[    1.924000] Unable to handle kernel NULL pointer dereference at virtual address 00000009
[    1.924000] pgd = 0000